fix-my-printer

4028 fan to toolboard 5 messages

Jul 27, 2026, 10:20 AM other setup

EBB42 X endstop not working 2 messages

Jul 25, 2026, 8:44 PM setup

VC3 500 Layer Shifts Help PleaS 140 messages

Jul 25, 2026, 1:29 PM other

Adxl345 problems 10 messages

Jul 21, 2026, 5:00 PM setup

Increasing offset between toolheads over the size of the bed 4 messages

Jul 20, 2026, 1:14 PM motion

Probe samples exceed sample_tolerance 2 messages

Jul 17, 2026, 8:45 AM other setup

RatOS v2.1.0 layer shift due to motor current 2 messages

Jul 13, 2026, 8:15 AM Solved setup

Need help carrying out why webbing 9 messages

Jul 13, 2026, 12:11 AM other

Erratic extruder temp behavior 12 messages

Jul 10, 2026, 9:22 PM other

4.1 belt calibration - still loosen those screws? 3 messages

Jul 9, 2026, 4:45 PM setup

VOAC components not working 22 messages

Jul 8, 2026, 6:11 PM setup

Where Can I buy PT1000 Replacement Sensors 4 messages

Jul 6, 2026, 2:37 PM other

VCore 4 Idex - Upgrade RatOS - Sanity Check 10 messages

Jul 2, 2026, 12:39 PM motion setup

Having problem with VAOC 3 messages

Jun 30, 2026, 10:34 PM other

VCore 4 suddenly stopped 20 messages

Jun 24, 2026, 12:08 AM other

VCORE 4.1 IDEX flashing and mcu error 8 messages

Jun 23, 2026, 11:17 PM setup

Warning: Unknown g-code generator 2 messages

Jun 21, 2026, 9:43 PM setup

New Commission Orbitool O2s won't enter DFU 4 messages

Jun 11, 2026, 5:58 AM setup

Oscillations when printing large Cylindrical features 5 messages

Jun 5, 2026, 7:46 PM motion

Rat-Rig 4.0 IDEX Z-Endstop not Working 4 messages

May 28, 2026, 1:33 PM setup

Stepper drivers 2 messages

May 28, 2026, 7:18 AM setup

New VC4.1 500 Hybrid steel gantry issue 5 messages

May 25, 2026, 1:13 AM motion setup

Rapido plus 2 UHF wont heat 25 messages

May 21, 2026, 12:53 AM other

Setup issue with pre assemled v core 4 idex 500 3 messages

May 18, 2026, 6:22 AM motion setup

New VC4.1 500 Hybrid z-motor axis too tall? 5 messages

May 18, 2026, 4:57 AM motion Solved setup

Error Prime Blob gcode 3 messages

May 17, 2026, 12:50 PM Solved other setup

VCore 4.1 Beacon Calibration: Z Endst always "Triggered", on Initial Approach bed travels -Z forever 3 messages

May 13, 2026, 3:23 AM motion Solved setup

Inverted x-axis 2 messages

May 13, 2026, 12:11 AM motion

V-Core 3.1 Adaptive Heatsoak 2 messages

May 10, 2026, 4:47 PM setup

Alignement of the X gantry 2 messages

May 6, 2026, 9:41 PM setup

Beacon setup no beacon model loaded 2 messages

May 4, 2026, 11:33 AM setup

beacon troubles after update and calibration 5 messages

Apr 28, 2026, 1:21 PM motion setup

RatRig reboots only during real mains outage (UPS switchover) – Bambu printers on same UPS stay on 9 messages

Apr 25, 2026, 12:00 PM other

IDEX Toolhead Offset Drifts 21 messages

Apr 25, 2026, 11:23 AM motion

Endstops always triggered V4.1 IDEX 14 messages

Apr 24, 2026, 1:34 AM motion setup

MCU timer too close error 6 messages

Apr 23, 2026, 6:09 PM other

Heavy duty idlers leaking oil? 3 messages

Apr 23, 2026, 8:08 AM motion other setup

Vcore 4.0 ASA issue 13 messages

Apr 22, 2026, 2:50 PM other setup

Disable Tangle Detection on LDO Smart Filament Sensor 10 messages

Apr 22, 2026, 10:44 AM setup

Fried Power Supply 15 messages

Apr 21, 2026, 8:41 PM other

T1 Dropping Connection - How to troubleshoot? 13 messages

Apr 18, 2026, 11:01 PM other

Timelapse enabled and configured but not working? 2 messages

Apr 18, 2026, 10:25 PM Solved other

Printer rebooting mid print 3 messages

Apr 17, 2026, 7:08 PM other

Z-Tilt map 37 messages

Apr 17, 2026, 1:26 PM motion setup

Toolhead 1 MCU disconnecting randomly, even when not in use. 7 messages

Apr 14, 2026, 4:31 PM other

v-minion nach Welcome to RatOS v2.1.0Base image: RatOS v2.1.0 (bullseye)Updated to: v2.1.0-0-g0be 2 messages

Apr 12, 2026, 5:25 PM setup

Is this mesh caused by a skewed gantry? 2 messages

Apr 11, 2026, 6:40 PM setup

Z tilt not measureing where it should 4 messages

Apr 7, 2026, 9:18 AM motion setup

Heatbed automatically goes to 100% once plugged in 15 messages

Apr 7, 2026, 1:35 AM other

Problems with bed leveling despite Beacon – systematic error 4 messages

Apr 4, 2026, 8:26 AM other setup