ratos-support

I know RatOS doesn't want me to use a can bus.... 11 messages

Oct 19, 2023, 2:21 AM Configuration

Question 7 messages

Oct 16, 2023, 2:41 PM Customization Other

Webrtc camera stopped working 9 messages

Oct 15, 2023, 9:48 PM Configuration

Connecting Orbiter V2 filamnet sensor to EBB42 14 messages

Oct 15, 2023, 4:37 PM Solved Configuration

KUSBA cannot get to work 10 messages

Oct 15, 2023, 3:57 PM Solved Errors

killer error after hard reset 2 messages

Oct 13, 2023, 3:59 PM Errors

Probe Points in Resonance Tester 5 messages

Oct 12, 2023, 1:54 PM Solved Configuration

Adaptive Mesh not working 2 messages

Oct 11, 2023, 4:42 PM Macros Configuration

Ratos 2.0 update and copying printer config 2 messages

Oct 11, 2023, 2:11 PM Solved Configuration

MCU 'toolboard' shutdown: Timer too close 6 messages

Oct 4, 2023, 10:03 PM Boards

Ethernet Static IP with M8P/CB1 2 messages

Oct 4, 2023, 10:54 AM Solved Boards

Octopus 1.1 detected but unrespnsive 10 messages

Oct 3, 2023, 9:59 AM Solved Errors

Weird communication issues out of nowhere 182 messages

Oct 2, 2023, 1:34 AM Errors

Network/connection issues 2 messages

Sep 30, 2023, 12:07 PM Solved Configuration

Multiple printers, one RatOS installation 2 messages

Sep 28, 2023, 8:29 PM Solved Configuration Customization Other

SuperPinda 5 messages

Sep 27, 2023, 6:20 PM Solved Errors

Tach is not reading correctly at high speeds 2 messages

Sep 23, 2023, 4:54 PM Solved Errors

Acceleration does not change from first layer accel. 6 messages

Sep 23, 2023, 3:37 PM Configuration

Nidec 4028 Fan 4 messages

Sep 23, 2023, 12:38 PM Solved Configuration

brcmf_cfg80211_scan: Connecting: status (3) 2 messages

Sep 21, 2023, 4:42 PM Configuration

Manta M4P v2.2 / CB1 v2.2 - RatOS WIFI AP up only for seconds 26 messages

Sep 21, 2023, 4:11 PM Solved Boards Other

Manta M8P v2.0 support 13 messages

Sep 21, 2023, 2:32 PM Info Boards

New VC500 config issues, specs below 9 messages

Sep 19, 2023, 6:52 PM Solved Configuration

Version: v0.11.0-275-g8ef0f7d7-dirty 2 messages

Sep 18, 2023, 7:44 PM Solved Errors Configuration

QUICK Q, is this the correct RatOS image for a RP4B 4GB? 2 messages

Sep 18, 2023, 5:17 PM Solved Configuration

mcu shutdown Timer too close - Octopus, Pi4, Vcore3, 500 3 messages

Sep 17, 2023, 10:47 PM Errors

What is the velocity limit imposed by ratos 3 messages

Sep 17, 2023, 10:20 PM Configuration Motion

Unable to parse option 'pid_Kd' in section 'heater_bed'. 7 messages

Sep 17, 2023, 12:56 PM Solved Configuration

Controller and Pi fan question 5 messages

Sep 16, 2023, 6:13 PM Solved Configuration Boards

BTT OCTOPUS PRO H723 V1.1 Firmware flashing problems 2 messages

Sep 16, 2023, 4:31 PM Boards

EBB42 x endstop not functional 8 messages

Sep 15, 2023, 7:23 PM Solved Configuration Motion

Start printing when (extruder) temperature is reached 2 messages

Sep 13, 2023, 9:00 PM Configuration Macros Customization

Klipper reports printer is not ready....was working a few minutes ago.... 5 messages

Sep 13, 2023, 12:06 AM Errors

Configuring 2 Pin Fans 4 messages

Sep 12, 2023, 8:34 PM Configuration Boards

quick question about prime blob(help please) 6 messages

Sep 12, 2023, 2:56 PM Macros

Tool board stepper motor setting 13 messages

Sep 12, 2023, 2:19 PM Solved Configuration Motion

cant upload my wifi credentials via the ratos hotspot.. 37 messages

Sep 12, 2023, 10:35 AM Errors Other

voron 2.4 experimental SB2209 6 messages

Sep 11, 2023, 6:28 PM Boards

42BYGHW811 stepper motors 2 messages

Sep 11, 2023, 2:19 PM Motion

network issues 5 messages

Sep 10, 2023, 10:31 PM Configuration

SKRat PT1000 2 Wire Temp. issue 7 messages

Sep 10, 2023, 9:29 PM Solved Errors Configuration Boards

RatOS can bus network cannot be created? Network is always "down" despite proper configuration. 2 messages

Sep 10, 2023, 12:11 PM Configuration Other

Update manager shows several "Invalid" 2 messages

Sep 8, 2023, 7:23 PM Errors

RatOS2 issues with PT1000 8 messages

Sep 6, 2023, 6:14 PM Solved Configuration Other

usb cams suddenly not working 13 messages

Sep 6, 2023, 2:39 PM Solved Errors

Joining wifi network that doesn't require a password 5 messages

Sep 5, 2023, 12:43 PM Configuration

Z offset problem 21 messages

Sep 2, 2023, 10:12 AM Solved Errors Other

primeblob 13 messages

Sep 1, 2023, 9:48 PM Macros

extruder rotating in opposite direction 2 messages

Sep 1, 2023, 3:00 PM Configuration Motion

I have a problem 40 messages

Sep 1, 2023, 7:26 AM Solved Errors Configuration