ratos-support

Issues with fine tuning Beacon contact 2 messages

Nov 18, 2024, 4:15 PM Configuration Motion Other

No trigger in probe after full movement 5 messages

Nov 18, 2024, 1:24 PM Configuration

RatOS - No network connection available 18 messages

Nov 18, 2024, 3:14 AM Solved Configuration

webcam stream not found 37 messages

Nov 17, 2024, 4:21 PM Errors

(vaoc) webcam stream not found 3 messages

Nov 17, 2024, 2:56 PM Solved Errors

Temperature List for T1 5 messages

Nov 17, 2024, 12:28 AM Solved Configuration Customization

Ebb42 not connecting tried following the step but doesn't connected 7 messages

Nov 16, 2024, 5:37 PM Solved Boards

How to set the correct camera to VAOC? 4 messages

Nov 16, 2024, 9:47 AM Solved Configuration Customization

unable to open out gpio chip line 16 messages

Nov 15, 2024, 9:10 PM Errors

Smart Filament Sensor Unload button Action not triggering 39 messages

Nov 14, 2024, 9:26 PM Solved Errors Configuration

Wrong pin assignment for T1 part cooling fan 8 messages

Nov 14, 2024, 8:13 PM Solved Configuration Boards

New Y endstop position 7 messages

Nov 14, 2024, 3:35 PM Configuration

Issue: pin heater_bed_heating_pin is an alias for PB2 18 messages

Nov 12, 2024, 3:07 AM Solved Errors

Trouble setting up webcam 9 messages

Nov 9, 2024, 8:57 PM Solved Configuration

IDEX and T0 T1 not matching print coordinates (x shift) 62 messages

Nov 9, 2024, 4:50 PM Motion

VOAC Z-Endstop calibration crashes into cam 75 messages

Nov 9, 2024, 12:14 PM Macros

VAOC issue (x offset on T0) after last RatOS update 81 messages

Nov 9, 2024, 9:52 AM Solved Macros

"gcc: fatal error: cannot execute 'cc1':; execvp: no such file or directory" when trying to flash 8 messages

Nov 8, 2024, 7:45 PM Solved Errors Configuration Boards

Unable to write tmc spi 'stepper_z' register GLOBALSCALER 428 messages

Nov 8, 2024, 7:00 PM Solved Errors

How to use an alias assigned pin for something else 6 messages

Nov 7, 2024, 5:18 PM Solved Errors Configuration Customization

I want to use another camera for VAOC 5 messages

Nov 7, 2024, 11:43 AM Solved Configuration Customization

No chamber heater found 20 messages

Nov 6, 2024, 6:02 PM Configuration

VAOC not loading and Realtime analysis giving errors.... 36 messages

Nov 6, 2024, 4:18 PM Solved Errors Configuration

Klipper Shutdowns 12 messages

Nov 6, 2024, 2:55 PM Errors

SAVE_Z_OFFSET always saves to beacon model offset 49 messages

Nov 6, 2024, 5:39 AM Solved Configuration

Error after updating board 3 messages

Nov 6, 2024, 4:56 AM Solved Errors Configuration Boards

Smart filament sensor for Orbiter v2 configuration. 23 messages

Nov 5, 2024, 9:20 PM Configuration

My ratrig V4 can not maintain temperatur stable 63 messages

Nov 5, 2024, 8:14 PM Errors

No Beacon model loaded 5 messages

Nov 5, 2024, 8:03 PM Errors Configuration

TMC error upon start up of my VC4. 8 messages

Nov 5, 2024, 7:06 PM Solved Errors Configuration Motion

How to upgrade from ratos 1.2 to 2.2 ? 5 messages

Nov 5, 2024, 6:23 AM Solved Errors Configuration

Nozzle getting closer to bed as it prints first layer 19 messages

Nov 4, 2024, 1:24 PM Errors Motion Other

Initial approach of beacon not working when the heated bed or hotend is heating. 38 messages

Nov 3, 2024, 11:36 PM Solved Errors

goop on nozzle after prime blob 4 messages

Nov 3, 2024, 3:12 AM Macros

Load Filament Macro Move Out of Range 13 messages

Nov 2, 2024, 11:12 PM Errors

MCU Timing Error 13 messages

Nov 2, 2024, 3:05 PM Solved Errors

_USER_END_PRINT_PARK Macro misbehaving 28 messages

Nov 1, 2024, 8:35 PM Macros Customization

Need config help on adding a section for a second part fan 5 messages

Nov 1, 2024, 7:49 PM Configuration

IDEX Misses Z moves 7 messages

Nov 1, 2024, 7:17 PM Solved Configuration Motion

gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode' 122 messages

Nov 1, 2024, 6:13 PM Errors

Print freezes, unrecoverable. 59 messages

Nov 1, 2024, 2:48 PM Errors

TMC ‘extruder’ reports GSAT 10 messages

Oct 31, 2024, 8:34 PM Solved Errors

Installing RatOS on BTT Pi2 and octopus pro v1.1 h723 6 messages

Oct 31, 2024, 6:10 PM Configuration

How to avoid Y collision in IDEX configuration? 6 messages

Oct 31, 2024, 2:56 PM Solved Configuration

MCU shutdown: timer too close - after I start a print (quite a heavy file) 113 messages

Oct 31, 2024, 8:09 AM Solved Errors

Not understanding VAOC calibration 12 messages

Oct 31, 2024, 6:11 AM Configuration Other

Chonk Triple Z Beta testing. Need help 42 messages

Oct 30, 2024, 9:00 PM Configuration Motion

Update Manager doesn´t work 9 messages

Oct 30, 2024, 4:02 PM Solved Errors Configuration

Configuring without machine actually being done....? 7 messages

Oct 30, 2024, 2:26 PM Configuration

MCU 'mcu' configured for 180Mhz but running at 176Mhz! 32 messages

Oct 30, 2024, 2:02 PM Errors