#building-and-recc-chat
1 messages · Page 462 of 1
I ordered Ripjaws v for my x570
Thank you for responding.
TBH, just get a decently cheap case and a 5 pack of RGB fans for $35
Need something good too not too much cheap.
are nvidia graphics cards supposed to come with stickers
more specifically evga ones
You should have at least 13 scratch and sniff stickers with each graphics card
@lyric thistle do you know where they're located?
it's a matter of national security
I am a jokester
okay
but there should be one
nvidia green sticker right?
or maybe an evga one
i need mah stickers
Good luck my dude
Can someone put together a parts list for me?
I'm looking for around $1000 A little High end gaming pc
Looking to play Red Dead Redemption 2, GTA V, ARK, Atlas, etc
Oh and Rainbow Six Siege
I'm looking for like a RX 5700 XT or a 2070 Super performence lol
Not for $1000
Do you stream at all?
When the GPU you want is half your budget, it's unrealistic, to be honest
Yah you’re around $1300 for a rx5700xt or rtx 2070 super
how much is a little?
Because you're going to need a couple hundo
I can get you a 2060 super for $1000 with no drive
Any parts you can reuse from the current build?
Case?
Anything? Power supply?
I can go over to 1300
Just wondering if a 2700x would choke a 5700 xt lol
No streaming
Just smashing games
kk, that helps
This is what I have set up so far
I'm planning to sell my old computer with a 1660 ti in it
I'm gonna edit my list to fit the black and white build im doing lol
This'll be a good reference
thank you
Problem with the P300 is you need fans
Only comes with 1
and you need at least 3-4 total
https://pcpartpicker.com/list/XY4m3t this would be mine if I wanted to get a Rx 5700xt
That's not bad but x570 can be nixed until you get to 3700X IMO
Nah
Tier C, recommend at least B or higher
PSU Tier List 4.0 rev. 7.0 welcome to the brand new PSU Tier List! Created and maintained by @Princess Luna, @DatTestBench, @Stefan Payne, @GreatMasterAden, @PSUGuru, and @LukeSavenije Last Update: 19-01-2020 Tiering of various units is opinion based off reputable sources lin...
Ya, that's fine
Is there a better case with preinstalled fans?
Good one! That was going to be one of my suggestions
oo I think that'll go better
I am going with the 2700x as it still holds up well and the stock cooler is nice
I wasn't planning to get black and white build but when I had the build together, it was already like that so I wanted to continue with it
You really should keep the 3600. The 1% lows with the 2700x might drive you nuts. Especially at 1080p
Is the 3600 better than the 2700x?
yes
3600 it is lol
Ok just wondering
I might change cooler but thats about it
Find a prism cooler lol
Also
whats a good mobo to go with the 3600?
I dont need wifi btw
perfecto
ASRock X570 Phantom Gaming 4 ATX
Powercolor and Sapphire are the best 5700XT options
ah okay
Think Gigabytes Windforce should handle okay?
@muted patio
not windforce woops
wait no
itis ]
lol
lol
I'm debating over Sapphire Nitro+ or Gigabyte
Gigabyte it is lol
looks like I'll have to save some extra $$$ but should be pretty easy over summer
I mean, you could get the rest now and get the GPU later or something
Or if you're going to wait for summer, the market could change quite a bit by then
might be worth reviewing the build again come summer time before you buy everything
yep
I'll check back every time there are sales and such to get the parts when they are at the best price
I meant new products could come out
So, I would just save all your money until you're ready to buy and review the build again
Hopefully I can have the parts together this summer
No. All you have to do is turn on XMP. That's it
ok i saw something about timings and i was worried
and how will i know its clocked at 3600mhz
do i go back into the bios
You set it. Save and Exit. And forget about it
Oh and I should probably set up Windows 10 usb and stuff like that lol
I wouldn't do that until you're ready to install it
With all the updates between now and then, just grab the latest build when you're ready
mhm
M.2 or SSD?
I know the market between there changes a lot
so
hoping to store windows 10 on it and maybe 1 or 2 games
Honestly, SSD if you're on a budget
The boot times and game load times are identical
SSD is cheaper
I laugh everytime my friend tells me to get a m.2
Cant tell a difference between SSD and M.2 speeds in practical use
I mean, for certain things they're fast. but every day use it really doesn't matter
He also gets confused when I load in faster
And before one of you fuckheads inevitably asks, no, jerry the goatfucker was not a real catholic saint.
Intro and outro song:
"Brandenburg Concerto No. 4 in G, Movement I (Allegro), BWV 1049" Kevin MacLeod (incompetech.com)
Licensed under Creative Commons: By Attribution 3...
this is the best video on the interwebs
Reason: Bad word usage
Sam O nella is the poop
Very build chat relevent
mhm
apologize my dear lord and savior.
M.2 is SSD 
its a port that ssd's can be plugged into, like a pcie input
But
Yeah, it is. Easier to keep them separated. Most people call a 2.5" drive an SSD, and the M.2 is, well, M.2 or NVME
M.2 or SSD suggests that there is no SSD to be had with M.2
It's like calling Windows PC
Heathens
Can I just shove the 24 pin cable into the psu shroud
Yep
ok yeah
but it has to be plugged into the mobo
the rest of the cable can hide under the shroud
just be careful, if the back panel is glass you dont want a lot of pressure on that glass
from what i can see it looks fine
good
@manic knoll
Yea I’m here
Stupid question. Recently I downloaded the sims 3 and 4 for my wife to play on my pc while I’m at work and she’s been having a problem where the monitor says there’s no input even though she can hear the in game audio. Also, the fans speed up to what I can only assume is 100%. It doesn’t make sense since the CPU temp is only like 45 C and the GPU demand is only like 30%. Trying to figure out wtf is happening
okay do you have the pc right now?
Unfortunately no. She just called me while I’m at work and told me that it happened
what are the specs of the pc and what monitor
Is the GPU overclocked?
its going to be hard to troubleshoot without having access to the pc
I’ll list everything in it:
Ryzen 5 3600
16 GB G Skill trident Z 3600
Red Dragon RX 5700 XT
ASUS TUF Gaming X570 plus
@junior pine no. Nothing on the pc is overclocked
Only the sims has this issue?
Yea I’m sorry @sacred obsidian. I could try to find something out tomorrow when I get home
what monitor
Your other games are fine?
Yea. I don’t play many games but I play d2 and the Witcher 3. Both of which cause the GPU to damn near max out since I run them at 1440p
I’ve messed around with apex too but I’ve never had that issue
Pretty sure it’s this one LG 32GK650G-B 32" QHD Gaming Monitor with 144Hz Refresh Rate and NVIDIA G-Sync
I would say driver issue. Or perhaps the AMD software is overclocking without you knowing.
i can find 2 solutions, one, update gpu drivers. 2 go to sims folder, find options.ini and open it in a text editor, find resolution, and set resolution to the resolution of your monitor
There was a driver update that I saw when she FaceTimed me but I wasn’t sure since I hadn’t had any issues until she started playing that game
So the resolution could me causing the issue? Wow
from what i found. some people fix it by updating gpu drivers, and another solution is to manually change the resolution in the folder
I saw what the sims 3 looked like and it looked like a freaking ps2 game lol
did she try both or only one?
Awesome. I’ll see if I can talk her through it
She only downloaded the drivers when I told her but I also wanted to see what would be another thing to try if that didn’t work
yeah i would try updating drivers first, if that doesnt work, try to change the resolution manually. if its set at 720, set it to 1080. if its set to 1440, set it to 1080. if its set to 1080, set it to 1440. see if that works. if it doesnt work at 1080, try at 1440 or vice versa.
Will do. I’ll try to talk her through it and if not then I’ll try it when I get home in the morning. Thank you so much!
no problem. let us know how it goes 🙂
Will do 👍
Yo
Nothing yet
😶
Like imma work and all the money I get imma buy a pc with
I need a upgrade my monitor also
ok, come back when you have as much money as you wanna spend on a pc
Well you said $250 before, but that's not a realistic budget for new parts and performance
you dont wanna decide before you have the money because the recomended parts now could be woefully out of date in a couple of months
^
the way pc building works, is when you plan out the build, you purchase components literally the same day
Not really, it just means current viable parts might be cheaper, they won't magically suck all of a sudden
or at least within a week or 2 lol
that way we can find sales and deals
Yea true
just let us know the day your ready to order parts
I was planning to get a i7 7700k for sure
.... Bad choice, bad value
Ight see you with this convo of like 4 months
lmao basically
True
10nm*

Ebay was selling a 2080ti for 75$
Yea
they arent doing 10nm consumer desktop
thats why i said 7
and if they did, they wouldnt even perform as good as their 14nm
All I need to do now is get a moca setup
Intel's new process is 10nm it's what they plan on doing 11th gen on... If they ever stop pushing it back
Bec google Wifi is garbo for gaming
at some point, their R+D team working on 7nm will be ready for market
remember this
lmao
o wait
$11k
Why in the world is there a cpu worth 11 grand
its first gen intel scalable
What does that mean
back when intel had the market in a stranglehold
and they could charge whatever the fuq they wanted to
Oh wow
@rough hornet what's your ISP?
Comcast
Have you tried using a wired connection instead of wifi?

Ethernet is cheap, and easy to tape to a baseboard you can easily run it
You just don't wanna
Well I like to keep my house looking professional and not some makeshift type stuff
And Idk if Ethernet support gigabit net
it does

there is 100Gb ethernet
Isn’t there like many types
yep
Then don't complain about your sucky connection when you choose to use a mesh wifi
a CAT 6a cable is all you need, just make sure your router supports gigabit
You get more bandwidth with an ethernet than you will with wifi, also less latency
?
Or wb a moca adapter or is a too costly
idk what that is
what?
why overpay for that
just get a huge ethernet cable
or move your modem router
or move your pc
It uses the coaxial in the house
so you wanted to run coax through your house?
Or maybe this
You could just run a flat white ethernet
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
^
^
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
is it tho?
And wouldnt the bandwidth decrease after like 100ft
No
Oh
Ethernet is good for 300 feet
Oh ok
after that it gets spoopy
Oh I can just move the whole damn Wifi into my room
Cat 6 Ethernet Cable 100 ft Flat White, Slim Long Internet Network Lan patch cords, Solid Cat6 High Speed Computer wire with clips & Rj45 Connectors for Router, modem, faster than Cat5e/Cat5, 100 feet https://www.amazon.com/dp/B00WD017BG/ref=cm_sw_r_other_apa_i_C-ujEb3AQ1ZVE
you only just now thought of moving the modem/router to your room
But that would cause lots of radiation and cancer and decrease your life expectancy

nope
That is why it’s in my brothers room
ok thats reasonable
Lmao
heh
I have the other mesh with google home built into it
trust me, thats not how radio waves work
yeah, that mesh needs to go
cuz
thats ur problem
EMI is what interferes with wifi
You are constantly being it with much stronger radiationthan your WiFi every time you go outside

Lol
Idk I’m just getting a lot of this crap from here lmao
lmaooo
That website is like a prepper/conspiracy theorist website selling garbage to the uneducated
Oof
If you beleive everything on the internet anti-vaxers win
My point exactly
They tell you it's bad to sell you garbage products
You get more radiation flying than you do in a lifetime of body scans at the airport.
🤔 just curious, how old are you Titan?
titan were sorry, that was rude of us
I’m 11
well, rude of me
Fun fact: Bananas are radioactive
I was about to say 11 makes sense for beleiving everything you read

How old are u guys if you don’t mind me asking
28
Boomer
Ok boomer
Ok boomer next!
40
40 isnt a boomer, thats a gen X 🤔
To the kids in here, it's Boomer
Is the wifi = cancer chat troll? or nah
i dont think so
It wasn't but it is now
just uninformed
oof
YO CAN WE GET A BOOMER ROLE
Boomer lyfe
I think you'd be surprised how many would have that
So all I need is a usb c to Ethernet
bekora you're just working your way into everyones name
And the WiFi in my bedroom and I’m set
I prefer to get called a gen y... Cause "millennial" is associated with being whiny and entitled

gen z
rip
yeah
Wtf it has 4 usb type c ports
I have the maxed out one
Idk what pc specs were back then
Im a dumbshi
my laptop got ports 4 days
next is gen Ħ
I had to spend I think 4K
fr
ouch, 4k on a mac
then gen .
.
B͑́̽
.
.
that wouldve gotten you a pc with a 2080ti
aw most of it dissapeared
It has a i9 with integrated graphics
4tb storage
yeah, you can to all that but better for 2k
And let’s not forget the turbo boost with touchbar
"turbo boost" on something that can't run an i9 and cool it properly
10tb with raid? Hmm
Nice joke
I do
then wtf is that
A nas
o storage
My pc being runned by it
when ur laptop dies, all your data goes with it
until you get another apple laptop
man they got you good
Apple products are extremely expensive, a computer 1/2 the cost can run circles around yours 
Can't beat my laptop setup tho
Wtffffff
my laptop on the right
Lol that keyboard 😂
Lmao
it cost more than the laptop tho
I hate my keyboard it’s too loud
its also the most expensive thing i own
It looks Soo bad though XD
it types like a DREAM
The k95 rgb plat with double shot pudding keycaps
I bet it does
my $600 board with capacitive buckling spring
I like my 200$ board with speed switch that sounds like a motherboard snapping every time I click a switch
Pretty lights
Idk where my pic went for my setup
i like purple
Imma find it
Take a new one
I encourage you to slowly phase out your apple products, you'll have way more money for things that are fun, or actually perform
but you obviously have some money invested in those apple nas drives
although, they probably have decent resale value
what drives are inside?
I’m make movies and I need those 20tbs
wdym movies
This build cost me well under 1k https://www.userbenchmark.com/UserRun/15630880
if your video editing and the like, apple is fine
I’m a YouTuber soo yea
Final cut is very easy to use, but not very useful overall
If you enjoy the creative/artist component of all this far more than the nuts and bolts and wires, and your time is more valuable than the opportunity cost - apple is an easy pick imo.
I use all adobe
Video editing on a Mac isn't really "better" anymore
250gb of ram on new iMac Pro
Eh - photoshop 6 is the last version to prefer OSX iirc, back when the IBM POWER chips seemed to be on a good track. Intel just left everyone in the dust with Xeon E5 though.
Either way - it's not usually a deciding factor, videos render, I take a coffee break, nbd
I highly recommend solid sate storage on freenas and or a cloud backup solution
I was planning to buy an egpu
It is a lot cheaper to have a hackintosh instead
bleh
g a e m
How many drives per array? How many allocated to parity? Raid 5 alone is a bit of a nailbiter when one has to rebuild arrays
But are you really ok with paying 3 times normal price for machines that underperform? 
Yea I seen that from Linus tech tips
Is this good matx
@eager chasm - Like I mentioned earlier - some people have valuable time
When his raid-5 array crashed
it looks like a nice case
@celest horizon yea which makes paying more for less kinda backwards
It's not less if you save opportunity cost in the aspects I mentioned
But that's a case-specific call
@celest horizon you do know I'm talking about paying $4000 for an i9 MacBook that can't even run the CPU and cool it
🤔
Oh the 2018's were prettybad, the 2019's had problems in bootcamp iirc
AMD GPU?
the 5500xt is alright, but overpriced iirc
It's a bit of work to get anything big and green into a hackintosh, or any apple
5500 XT is pretty much garbage
lol
Better than 1650Ti, cheaper than a 1660S 
just a little bit extra can get a 1660 Super which would out perform the 5500 XT by so much
yeh
5500 XT is like what 20$ less from the 1660 Super
but the performance is like 50% more about
doesnt the 1660s preform real close to the 1660ti?
about 15% less from the Ti model
yeah
It’s there any way to have a maxed out pc and still run Mac like I’m takin i9 with 4 2080tis and 128gb ram bit run Mac like the whole restart and hold option key and that stuff
theres like a 100$ price diff
I don't see any price drops https://i.gyazo.com/b2051f00d46544c45ffcb91d2adaf2cb.png
There were some for just $160 the other day
That is also 4gb
which is even lower in performance
yeah i kno
and that has been the cost for the 4gb cards for a long time now
just no one really wanted a 4gb card they wanted a 8gb card
yeahh, i actually didnt realize there was a 4gb and 8gb version
i just knew they werent worth getting lmao
could of been on sale
most likely
Its a good deal at that price
I wouldn't be surprised if the 5600 XT ends up flopping
Do many games at x settings push up on 4GB vram? -for that GPU's market segment
said to be like 270$ for the 5600 XT and if it performs like the 1660 Super that will cripple AMD
doesnt an RX 590 8gb slightly outperform the 5500xt anyway?
@viral ore by like 2-4 frames
Ram is cheap now, it used to be expensive
yeah, theyre performing really similarly
Gb
Yea that's cheap
and with everything going on now for the RTX 3xxx series the mid range GPU's might murder the RX 5900 XT
cheap as dirt
yeah, and you probably paid 350 for the ram in your laptop
AMD just took too long on making it up to their high end card
Yea that's the more premium stuff and that's still a good value
I only got 8gb ram
When I build my computer 2 years ago the "budget" 16GB kit was $180
yeah
Haha damn, I remember 3200c14 flarex being 200 for 2x8
2 years ago i bought my 16gb kit for 100$ Canadian 😛
It's been as low as $100 lately, but 115 now
😂
i9 mobile is 9th gen only
For AMD to actually make a breaking point for the GPU's they would need to make something like Navi 56/Navi 64
iris is different. i9 9900k has regular hd630 - it's pain
2080 ti still clocks down to 300 mhz idle
That’s like pesent scores
No reason to burn power at rrest
Intel integrated graphics suuuucks 
Sometimes I throttle because of overheating I loose like 60fps
water cool it
quicksync is pretty useful though, and it's nice for troubleshooting, fun for some oc bench runs
Hey Intel iGPU is good for PS1 emulation 
Haha my ice pack helps
@viral ore macbook
Macbooks are giant jokes 
I've switched between a few times - can't stand the comfy layout on laptop though
understandable
Man I’m like sucking the life out of the Mac
It’s like at 95c at max
yeah, thats slowly killing the silicon
Then you can build a real computer
It’s life span isn’t doing well

Coffee lake refresh can take heat well enough it's a non-issue for the chip itself for the vast majority of apple user use case
interesting
Now - their decision to route a 55 volt lead right through the middle of the logic board - no words
Lots of in deptch critique over that in the rossman discord
The battery always scares me , irattionally mostly. but 80 watt-hours is about a hand grenade worth of energy lol
250fps on what settings?
Well, maybe half of one

Low settings and 100 3D res
zoinks scoob
What’s up with that build ?
not enough rgb ziky
Yup, not a lot 
Was just wondering if Galaxy needed help w/ anything w/ that build he linked
@elfin stone beautiful case man how you like it?
Hi
Hello : )
Hi i
I forgot to plug the RGB cable to the cpu cooler, would it be possible to run the pc for a few minutes to loosen thermal paste, turn it off and then remove the cooler to plug in the cable and immediately put the fan back on? Just wanna avoid buying thermal paste and reapplying it
yeah if thermal paste is fresh it shouldn't be a problem
Is the cable header occluded by the heat sink?
I'd just order a $5 tube of mx-4 or equivalent to have on hand for convenience
Okay
if you like chinese, go for the 5/10 syringe packs of hy 880/810
Coffee filters work well IME, tbh I use paper towel, then coffee filter/ISO
91% isopropanol from the drug store is fine. Or just buy a 50 pack box of those rubbing alcohol wipes for $2, both work
Hmm okay
Lol, I'll clean my prism stock paste now to test it - I need to remount anyway.
Lol okay thx
So paper towel and then coffee filter?
Not too hard
Use any water?
That's what I do - most people are very particular about how is best
I guess on important chips , I just use dry coffee filters for most of it, then 100% isopropanol - if your paste is more polar, maybe add a bit of water,
Unless you buy it from a chem supply co. - it's likely 91% anyway
I think mx4 would work
I recommend it because it's very hard to apply/mount incorrectly, low viscosity , less important to get solid mounting pressure
Great performance
@vestal cove it's ok but you can get a case just as good or better for less
Buying from the US? Looking to buy all newegg new? or some elsewhere/used etc?
Well there is this case which is just as good as the one he picked and gives 4 fans instead of 3 for less https://pcpartpicker.com/product/pCjJ7P/rosewill-spectra-d100-atx-mid-tower-case-spectra-d100
you could also buy Ryzen, save money, get a scalable system, buy a case and then fans separately, 32gbs ram, and a 2070 super, https://pcpartpicker.com/list/pz6gzN
for 1268.94 USD.
instead of your 2060, 16 gbs ram, and a low air flow case.
why exactly? your cooling a chip thats a year old, and its slower then the ryzen 3600X, which comes with a stock cooler.
and yeah the nzxt case has space for airflow.
It looks much better than the stock amd cooler
The NZXT also comes with 2 fans.
NZXT 510 has poop airflow
That must stink
I would also probably get a 3600
get the 3600 over the 3600x unless sale price justifies it - grab a scythe ninja/mujen/gammax400 - or invest in a noctua/DRP4 w/e
Front intake is all of about 2 square inches
openbenchtable bc-1
wait
It has a slit for front intake on the left side.
Also 32gb of ram is a bit overkill
Very restrictive
are you buying things on looks, because @celest horizon is right, a nuctua cooler would be far suprioir.
and 32gbs ram if you can buy it, is still ram. it depends on what your planning on doing.
idk about far - I have a few - I'm mostly a fan of their build quality, fan MTBF, and most of all, the mounting hardware
What would be a good alternative to the 510 for him that keeps the same esthetics?
It's not far superior. It's on par with or slightly behind. nice thing about AIO's is the CPU heat goes directly out of the case in an exhaust configuration. A big air cooler in a case like the H510 isn't advised due to poor airflow.
White case?
yeah I hate decoration. rgb can go to the can for me. and last time I checked the NZXT H510 worked fine.
GPU exhaust has to be mindfully routed away from aio intake though
In the end - I think aesthetics, space constraints, preference will decide aio or not
acoustics to cooling it is far superior.
I think he's looking for the minimalistic design.
Did you watch the linus video?
Rather, is your opinion from that linus video or experience
The 510 is about as clean as you can get without it being too gamery.
I know the 510 isn't the best airflow case, but even I keep looking at it because it would best fit in in my living room.
Have you looked at the three I just posted lol?
I don't see a problem with the 510. Unless you have some extreme build/overclock plans - $20 in fans fixes all
^assuming your aesthetic preference remains to the 510
no my opion is from my own exerpince. when using the water cooler it had got heat socked, and refused to cool further, where as the noctua was easily able to keep temps the same the entire time. I watch gamers nexus.
incase your wondering.
And what AIO was it? if it was getting heatsoaked, it was an inappropriate size for the CPU. I'm guessing Threadripper..........
@muted patio I looked at the ones you posted. The Meshify is pretty subdued, but I don't see how the carbide is much better at airflow.
No holes
Fully open slots
Tiny holes like the 510 has are pretty restrictive, where an open slot is not.
It comes down to actual open surface area
I'll give you that.
I build and tune intakes and exhausts or my race motorcycles. It's really the same thing. Air is a fluid..........
nah it was a i9.
I agree with you. I just wish high airflow cases were a bit more subdued. Plain if you will.
Well, if you want high airflow, you need mesh in the front or something. The less air has to move/bend the better the flow
This is true. It's really a catch 22.
It is
Let's remember what's inside, how many watts really? 70 on the cpu, 200 on the gpu?
Not much , no?
Depends on the CPU
3600?
Remember, the TDP doesn't factor in boost or PBO
My 65 W CPU hits 105-110 regularly on PBO
I pay very little attention to tdp these days lol
Current clamp on the 12v cable doesn't lie like whitepaper specs lol
But ya - if you config EDC, other mobo OC options way up there, sky is the limit, well, 90c or w/e
Well I’m getting what I originally had
I might just change the 500gb m.2 to 1tb m.2 and remove the hard drive
@vestal cove I mean, you can also just get significantly more perf for cheaper. Slightly better CPU (even for gaming), and much better GPU
https://pcpartpicker.com/list/cnN44n
@vestal cove why intel?
holy crap this f.lux software is a life saver
https://fi.pcpartpicker.com/list/mqvQGc can som expert take a look and tell me spesifically will i run into any problems while building this like a BIOS update or do i have enough ports for the fan rgb in my mobo or will anything overheat? do i have enough space... and is my psu enough? I WOULD APPRICIATE it soooo soo much but i know its a lot of work so im not insisting anybody to do, Thank you and sorry for my bad english!
@charred flint So more of a suggestion for the SSD, the one you choose isnt actually NVMe, just SATA but in the M2 format. I usually suggest not doing that due to trying to upgrade in the future to NVMe but not having a slot. So go for this
https://fi.pcpartpicker.com/product/LRkj4D/western-digital-blue-500gb-25-solid-state-drive-wds500g2b0a
Everything should work. Havent checked the RGB lighting tho, so someone else can look into that
Hi, can someone help me with this?
ok when you replaced your cooler, did you take out your cpu at all?
or just the cooler?
The CPU cane out stuck to the cooler. I even ran stress tests before removing it to soften the paste but it was stuck. I didn’t see any damage to the pins though
I will remove the CPU later and see if it got damaged while installing it
use some rubbing alchol or hand sanitizer to try to loosen the paste
if you get some on the pins its no big deal you just have to wait a little for it to evaporate
if the cpu came out without being unclasped you probably damaged something so def check the pins
I used alcohol to clean the paste
make sure none are loose but becarefule not to bend em
other than that, try putting old cooler back on and see if it boots, or try using one ram slot to see if it boots
I already tried changing the RAM slots
try using a razor to re align the pins if you notice any bend ones
not a razor
why not?
A needle?
I don’t think the card would fit between the pins
basically when you put it in the slot, it should just flop down into place with no pressure
if it doesnt do that, you have bent pins
Yeah, I didn’t have problems installing the CPU
but if it does do that, since you pulled it out of the grip, you may have pulled something loose
so it may not look like a bent pin
also for future use, when removing a cooler, twist slightly to loosen as you pull it up but gently
When I unattached the cooler and it came out with the CPU, I didn’t really get a chance to twist it
thats what i mean, twist the cooler lol
so it doesnt rip the cpu out of the socket
I unattached the spring clamp and it just popped out, I didn’t even unlatch the other side
ohhh
weird.
i mean i get it
next time loosen each one before taking it off i guess?
but
try that cooler again to see if that might be your issue
also double check all your connections to make sure everything is in all the way
Ok, so I finished my new build: https://pcpartpicker.com/list/sQdTPn
I need suggestions for a better CPU cooler that's not too expensive and won't block my other ram slots, preferably downdrafting to help the VRMs
Also, some suggestions for additional/replacement case fans wouldn't go amiss
@cedar portal Is that what you have or will get?
that is my finished build sitting on my desk right now, yes i'm aware those hard drives are older, they've been good to me
Seems like that PSU doesnt have a very good surge protector, so you may want to consider getting one externally
that's not the exact one i have, I just remembered that it's 550 watt, but again, it's older, 80+ bronze i think
a new PSU is on the list, but I had this one and it's worked flawlessly for me so far
So I have a p400a case and a b450 tomahawk max mobo. As some of you might know rhe b450 doesnt have an argb header and the p400a case fans are argb. Is there any way to connect them or should I get a different mobo?
@cedar portal See, my problem with "so far" is that bad things can still happen. Kinda go by "Just cuz it hasnt happened before doesnt mean it's impossible. Example: me dying. I have yet to die yet Im still perfectly capable of dying". Im a bit of a PSU person, making sure you got a decent PSU that'll be good and such.
I will probably side-grade into this one when some more funds become available
https://www.newegg.com/seasonic-m12ii-evo-series-m12ii-520-evo-editon-520w/p/N82E16817151093
no, S12 and M12 are pretty bad PSUs, even if from Seasonic
@sacred obsidian I just removed the CPU and didn’t find any problems
none of the pins are loose?
try adding the old cooler back on and see if it works then
hi
bruh the 3 ppl i see everyday ever since i joined this discord a couple months ago is hei bekora and dragocor
hey
yeh?
whats going on
because
thats what we do here
mostly
if your here because you need help with newegg stuf, just dm @fresh garden
they will reply
at some point
no im just here because im like really bored and i need someone to talk to
o lmao
talk in general chat
good luck
@sacred obsidian Turns out the first two RAM slot don’t work
I guess I’ll have to RMA the motherboard
@cursive wharf would something more like https://www.newegg.com/thermaltake-toughpower-grand-rgb-gold-ps-tpg-0650fpcgus-r-650w/p/N82E16817153310 be a good idea?
were they dead or did you try to oc the ram?
usually the correct ram slots are the 2nd and 4th slot
from the left
They worked before installing the cooler
I had them in the correct slots at first but now 1 and 2 don’t work
hmm strange
I have them in 3 and 4 now
yeah i guess rma the mobo cause 3 and 4 isnt gonig to run properly
If I bought it from Newegg do I contact them or Asus?
July 2019
oof idk if they will take that at this point. maybe do try to contact asus
I’ll check what I should do
@muted patio or @celest horizon if a ram slot is working fine before a cpu is puled out of the socket (without the cpu lever being lifted) and then afterwards 2 ram slots no longer work, but the cpu appears to be fine, could that be an issue with cpu? i dont see why 2 ram slots would have just randomly died
he removed the cooler and as he did it pulled the cpu from the socket, but he says cpu is fine and it just falls in its slot like it should but now slot 1 and 2 are dead
i just have a feeling the mobo is probably fine and that the issue is still cpu
Well
if the lever wasn't lifted
Odds are good a pin got ripped off the CPU
and stayed in the socket
@next nymph could you take a picture of the cpu pins and the cpu socket?
Which means the socket is potentially dead also unless you can pick it out
I’ll see if I can remove it again
Life the lever this time
I checked the pins and they were al fine
I checked if they were loose and none were
And if you lifted the CPU out without lifting the lever, that's probably what happened
It was stuck to the cooler
yeah the spring pulled it up
That paste that the stock cooler comes with is quite bad
i just wanna inspect it and see if a pin is missing
I got lucky like that one time.
sounds like bent pins
went to remove the cooler and POP! whole thing slips right out
Could it be that the pressure of the new cooler damaged the motherboard?
i dont think so. the area around where the mounts are should be free of anything that could break so unless theres like an actual crack i wouldn't expect it to. it could have also been shorted on the underside of the board somehow but unless you removed the mobo i doubt thats the issue too

