#old-cooling
1 messages · Page 48 of 1
so uhh
I need some help
I've been trying to play valorant uncapped on max settings
and my gpu can do just fine BUT
it gets really hot and basically over 80ºc which is a nono
my case is a Coolermaster Masterbox Q300L with no extra fans
is there anything I could do to lower my temps other than get more fans?
I have an RX 580 8GB (Asrock phantom Gaming D model)
Open side panel
like I've been noticing my intake fan (back fan) makes intake air actually hotter because the back plate gets hot
Wait
Rear intake..?
that case looks like one that should have front intake rear exhaust?
@topaz blaze anyways a 'test' you can do is test it with side panel off, then test it with front filter off
also yeah seems like it
the rear seems to be intake ????
idk I didn't flip it but I think that's the case
yeah it's intake wtf coolermaster
I tested using a piece of paper
q300 has pretty terrible airflow IIRC
you should probably add two intake to the front and one exhaust at the top
and flip the rear fan around to exhaust
it's exhausting just checked
it should be better, but probably still not great
it's pretty hard to tell :/
also idk I mainly picked this case cause of airflow
most cases in this price range were even worse
here is a review of the slightly larger version:
https://www.youtube.com/watch?v=F3n80GxU-Zs
We tried hard to make Cooler Master's Q500L case perform well, but we just couldn't pull it off. The Q500L is one of the worst thermal performers we've ever tested.
Ad: Buy Gigabyte's Intel Z390 chipset Master motherboard (http://geni.us/eIQnI on Amazon)
Article:
Find the C...
anyway, 2 front intake and one more top/rear exhaust will probably improve things
pfft that case is way worse tbh
its the same design thing when it comes to air
damn
you can see how blocked off everything is when you take the front filter/mesh thing off
and its the same for both cases
3 more fans should improve things in your case though
My Brackets arrive tomorrow to install my Noctua NH L9i. exciting. I have to completely disassemble my SFF PC to install it lol
Is it possible to have too much positive airflow?
@dreamy cape there's the possibility of all intakes >:D
specific situation matters though
consumer cases = leaky boats
ya
Well right now I have 3 front fans pulling in, 2 top fans pulling and 1 rear fan pushing out
y
Should work fine
You can do whatever
what sort of thermal paste would you guys recommend to put on a 3900x/krakenz73 combo
looks like i could've possibly messed up a bit being as my friend runs around 60 degrees on max in cod and i'm at 70 degrees
no
@safe citrus temps are really hard to compare with each other
there are too many tiny factors you basically cannot control
especially in applications like gaming where even the load placed in the CPU varies greatly
well true but shouldn't i remove and re apply since it's only in a circle? idk isn't 70 degrees kinda high?
like the aio came with the thermal paste in a circle and i kinda removed it a few times to get it aligned the right way
circle?
70c isn't bad
oh if you kept re-mounting it
you might want to re-do the paste with a new tube
yeah i kept re mounting it so that's why mb wasn't clear lol
so idle temps are around 50s
which miiight be kinda high no?
meh
47-55ish
as I would say, all idle temps tell you is your room temperature :P
think it's worth re applying it though since i did kinda botch by re mounting?
yea
also could be different case
i wonder why the one on the left is cheaper
yeah
left is a simpler solution
hm
they include two rgb plates with the package, thats what was throwing me off about the price
same story with the 360mm ones
i have a frame for a pair of my skates, there is about 30% less metal in it. and it looks fairly simple in design. But because of the material it is made from. it costs about 3 times as much as a different more "flashy" frame
they price it in whichever way people are willing to pay
if that means the prices are bat fry crazy? well, that just tells you a LOT about how much logic people use when they buy things
i mean for the 360mm ones... you pay the same price but you get included rgb fans and the top of the pump is swappable
seems like youre getting more features for the same cost
but
¯_(ツ)_/¯
shrugs
Is getting AIO worth the risk of it leaking or is it better to stick with air cooling?
remember, it's a pretty small risk, and pricing matters imo :)
My suggestion is either go Arctic freezer ii for an AIO (100$ 240mm, 110$ 280mm, 125$ 360mm)
or high end air coolers like the NH-D15, CNPS20x, DRP4, etc.
I’m just worried about it leaking on to my rtx 2070 super gpu
hi there, anyone know a sub-80 dollar watercooler for my cpu?
do not buy a watercooler from wish
idk
For that price air coolers will be much better
just cooler temps
air coolers can cool just as well as water
yea
at that price air coolers can cool at the same performance
maybe even better with the kind of liquid coolers you get at 80$ lmao
Get a gammaxx 400 or Mugen 5 rev b depending on how much you want to spend
aesthetics can go in the toilet
and flushed
performance ftw
Mugen5 looks nice, also shadow rock3 looks good too at similar price
Im not building my PC for another 2 months, but the water cooler I want is on sale for 25% off should I buy it?
what about not getting a watercooler
and remember, black friday/cyber monday and other major sales will likely have similar discounts
I want a water cooler
Why
Looks cooler/performs as good as I need it to
how good do you need it to perform
Cool a Ryzen 5 5600x, no overclocking
lmao
a better deal for similar performance
and you didn't even pick the actually good aio
because freezer ii isn't on sale
:P
The only AIO I approve of is the Arctic Freezer ii
everything else sucks in terms of price to performance
It's one of the best performing AIOs, and at the 100-125$ range from 240mm to 360mm
I'm not going to change my part list off of someone else's thoughts on discord, just simply asking if i should buy now or later
you shouldn't go off my thoughts
@lost hinge go off Steve's thoughts
https://www.youtube.com/watch?v=KPaSEGe6ML0
Our review and benchmark of the Arctic Liquid Freezer II features tests on the 3950X and 3800X, but also talks VRM thermals and whether the fan is a gimmick or not.
Sponsor: Get 10% off Squarespace purchases (https://geni.us/BqEpf)
Article version of this review: https://www...
also, this is exactly what I do in this discord all day soo ehm, I'm probably the wrong guy for you to talk to then. :P
Here it is also in article form if you like reading better
https://www.gamersnexus.net/hwreviews/3571-arctic-liquid-freezer-ii-cooler-review-benchmark
By the time you're done either watching or reading, gonna leave this statement again.
and remember, black friday/cyber monday and other major sales will likely have similar discounts
Yeah arctic has some excellent AIOs.
Yeah I used to care about them too until I realized in most cases a hefty price tag can come along with it "looking good"
performance over aesthetics
i mean if I am going to have a part I would rather spend more for it to look nicer
like the AIO I picked out should max my R5 5600x at 70C because I don't plan to overclock
what aio
httcorsair h100i plat
for a 5600 it should do better than 70
Evga clc 360 is better than arctic liquid freezer right
uhh is a low profile cooler rated at 110w good enough for, say, a 10700k?
I just got an email today from Lian Li saying they will have unifans 120 in stock on the last day of October. I’m planning to buy them soon as possible cause they may be sold out again after that date.
@empty sigil no
clc360 sucks compared to freezer ii
unless you like your ears being scratched from the inside
Can a techie help me
can any fan be used as an exhaust fan?
Technically yes.
Long as u direction it right yea
Static pressure as in balanced intake and exhaust?
Or is that just designed to be more appealing to use for the intake?
@light fog kind of, but yaknow, there's fans like the Arctic P12 that's designed as a pressure fan that's still great for airflow :P
Oh yeah for sure.
That's why I said any can would work when they asked the question.
It's just some are made for it.
Hey all, I have a question what is the best bang for my buck CPU cooler for and i7 7700 non k I have an HP IPM17-002 motherboard from an HP omen 870-219 prebuilt
but who knows if that MB has standard mounting hardware
@green oriole imo, absolute best bang for your buck is Gammaxx 400
20$ with performance that can beat a NH-U12s
Ty
@tame hemlock build chat
@hexed ledge this the fan i use its a little loud but since i only got space for two case fans i run this one bc its high cfm and fit my budget it works really well
Ah ok

Quietest cpu cooler?
Whats everyones opinion on this cooler. https://www.corsair.com/us/en/Categories/Products/Liquid-Cooling/Air-Cooling/A500-Dual-Fan-CPU-Cooler/p/CT-9010003-WW
Bring your CPU temperatures down with the CORSAIR A500 High Performance Dual Fan CPU Cooler, equipped with four direct-contact copper heat pipes and two CORSAIR ML120 fans.
Ive currently got the coolermaster hyper tx3
Looking to possibly swap it out
its a very expensive cooler that does not perform to what it costs @forest oyster
@subtle lodge Noctua D15 or similar
Ok
the fanless one:)
is the Cooler Master Hyper 212 EVO good?
ok
what about the Corsair H100i RGB PLATINUM 75 CFM Liquid CPU Cooler
@burnt goblet
Yea
ok thanks
360mm is better tho
couldnt find a 360
have to get 360mm supported case tho
case i recommend with arctic liquid freezer 360 is p500a
im in canada
Can I expect a be quiet Dark Rock 4 to efficiently cool a 5800x non-overclocked
I would’ve gone with a noctua if they were a different color
And spend money I dont want to spend. I’m not planning on overclocking so I should be fine right?
On the dark rock or were you talking about the Noctua
noctua
ppl oc it and get under 50c
On 4k
@burnt goblet serious question, nh d15 or arctic liquid freezer
If I get bad temps on my CPU I’ll switch to something else
Might aswell get nh-d15 then
I’m not spending $100 on a cooler if I don’t need it. I’m not over clocking and I shouldn’t be doing anything that’s gonna drive my CPU temps high#
ok
Just saying its a good investment either way
Future proof by oc
And good temps
Is there anything you should really be looking for in a fan hub?
Or are most decent
Can I expect a be quiet Dark Rock 4 to efficiently cool a 5800x non-overclocked
@gentle swan both are the same really except that noctua has a bit for performence and the be quiet one is a little quieter
also u can nd d15 in all black
i am also from canada
its on amazon
also since you are not gonna oc
there is no point in buying the best air coolers
on the market
you could get away with a way cheaper one
Stupid question but do fans exhaust from the front or back
Depends
I just bout a phantenks 300a and it has a small fan on the back facing outwards
I need support here I just got deadpool pack for case fan 5*1 and this is the product https://www.amazon.com/dp/B07HN199YJ/ref=cm_sw_r_cp_apa_i_aLWIFb6N4SWHH
And I have Aorus b450M motherboard
And I don't know how to install it how to connect to each fan to other with hubs and which one wire I put in motherboard...any help pls ?
Btw case model is Cougar mx330
Will install 2 in front that get in air and 2 top and rear for get air out
Thanks in advance
A higher end air cooler could cool the same chip more quietly
also since you are not gonna oc
there is no point in buying the best air coolers
Not true with Ryzen zen2 and on, the chip will "auto-oc" itself within thermal constraints
I haven't
for people like us, its not super filled with new info, but there are bits here and there
I have kind of a big problem with my fans
They have a motherboard type of thing
And it’s really short and just hangs there and idk what to do
Any suggestions on what to do?
@swift aspen velcro?
Arctic p12
I run 5 of the deepcool RF120M They are RGB not A-RGB. They have pretty good airflow for the price. about 50 bucks for 5
The 5 pack comes with a splitter that i used to connect the fans together and to 2 headers. Then all the connects together and then to the mobo.
it also comes with a small controller that you could use if your motherboard doesnt support RGB
Oil?
Dont buy it then
If anybody finds out when Lian Li unifan 120 will be in stock please let me know. I want to add them to my first build but they are really hard to find right now and are out of stock.
@tacit plaza u don't want those
not adressable
and it's right abt oil
they are very cheap, very bad LL fans
meaning they greased with fluid
don't buy those
consider buying from deepcool or something of the sort
Ah thanks will stay away 
so i got an nzxt 710i and i want corsair rgb fans will i have to buy the icue
and use a different rgb system
Dont buy it then
no but im asking will i have to use the corsair rgb control thing
Fuma, only because ninja only has 800rpm fans
If you have a low power cpu ninja will be quieter tho
Ninja can also have clearance problems with rear case fans of your case is tiny
Yes
Should i get z73 kraken instead of arctic liquid freezer
by now, you should know that asking the same quetion in 3 different channels is NOT going to earn you any favours
Are there any cheap 3 fan splinter?
@swift aspen splitter?
U think it matters if it’s used or not?
that is for you to decide
New ones are super cheap alreadt
anyone know when newegg will restock the lian li galahad 360mm aio cooler
No one knows
hey. what would be some decent quality cheap fans. i need atleast 9 fans for under 100
arctic has some nice black fans, i think you can get 10 for like $50
what about rgb ones
uphere rgb fans, u can get around 10 for 60 i think
can you possibly send me a link. i cant find any that cheap
Do those fans connect straight to the case?
Oh I meant mobo
afaik they dont, they come with a controller
and you plug them into the hub and use a remote
is the cooler master 240l radiator with fans good
Would these be good fans for a metallicgear neo qube https://www.amazon.com/gp/product/B07XDZC96K/ref=ox_sc_act_title_3?smid=A2A4XZZKQVDB4S&psc=1
Hello guys, so i want to upgrade my wraith prism. Any suggestion which one is better, air cooling or aio water cooling?
I need durability, because i move frequently and good cooling, for my 3D render and have a good price too
Hi
hey
I plan to have 5 RGB fans, but my motherboard only has 1 RGB port and 2 fan ports. Should I just get a splitter? Will there be any issues?
Something like this...
I need a good set of fittings for a custom loop. I want them to all look consistant, so I need a single brand with a single style. Color; preferably gold...
I need help my back exhaust fan starts up quiet then goes really loud
@pulsar comet you have connected it to the wrong header on the mainboard
it wont hurt it
ok
which model is your mainboard?
z490 e gaming
where have you connected your cpu fan?
ok
whitch one
and your BACK fan goes in number 3
ok
what cooler would be good enough for the 9600k oc to 5 ghz
okay
i am putting together a list for my friend and he wants to oc and i was thinking that since he is only gaming the 9600k would be perfect am i wrong about this
budget?
about a 800 - a grand
i dunno i will ask him
There's little reason, that's why I'm asking
can anyone recommend a good 1 or 2 fan black AIO? like no rgb
all black
lol this list has a 3070 and barely under 1000 its bad lol i made it as joke https://pcpartpicker.com/user/Fishii_bun/saved/sJsv3C
list be privat
Its private @pseudo rose
oh rip let me fix its a joke tho
I wanna see xD
same
beleive this is it
i did the same
my 3070 list is like 1035
nah still private
Still private
^^
i have one that is 1009
rip how make not private
3070 lists should preferably be around 1500
dont rember
i have one 1250
Click edit this part list
And then copy that
this is cooling
arctic liquid freezer
https://pcpartpicker.com/user/Fishii_bun/saved/#view=wB6VwP is it still private
nah
yeah that list is quite something
it was meant for joke lol my friend wanted a 1000 list 3070 he got mad i gave him bad list
https://pcpartpicker.com/list/wxyXPV here's mine
thats good but why did it have to be micro atx
micro atx isn't a bad thing
Cuz matx is cheaper
saves a lil money here and there
my friends dont like it they think theyll mess up
?? Why will matx make u mess up
your friends need to learn a thing or two about computers
idk they weird
Mhm
i would change the ram to something cheaper
true
on mine?
yeah
that is a good point i would have levatated towards the cl18 3600 but that would just be for me to save some moners
i got g.skill 3600 cl18 for $57 so im happy w/ it
@spare ember https://pcpartpicker.com/product/qQzFf7/oloy-warhawk-rgb-16-gb-2-x-8-gb-ddr4-3600-memory-md4u083618be rgb plus 3600 and c18
cheaper too
i'd still stick cl16
faster
i personally don't care for rgb much
but that's just me
lol
@austere quartz that cooler works fine enough. I am guessing you wanted it for the RGB?
nope, i would actually preffer no rgb
then why not just go air cooling?
https://www.newegg.com/noctua-nh-u12s-chromax-black/p/13C-0005-001H6 <- this solves things for you @austere quartz
same concept
another change @austere quartz
this has come back in stock
so grab that instead
same as the previous one i linked, just a tiny bit cheaper
:)
same perf/dur
cool, thanks
you are very welcome :)
remember to buy a usb stick IF you dont own one already for installing windows with
yeah, already have one, thanks for the reminder
you are very welcome :) best of luck with the system :)
RoG so expensive 
somebody send me a nice looking set of compression fittings, 6 pack, for soft tubing plz :)
Anybody had any luck finding the Lian Li unifan 120 in stock yet?
Xspc or bitspower make decent, cheap compression fittings
I’ve been trying to find the Lian li uni fans for weeks haha. Hope you find them soon!
How often do Corsair aio burst
I'm gonna be looking in november for fans for my case on my next build. I just want some good fans that don't have RGB. Not that I hate it, I just don't need it.
How often do Corsair aio burst
Not an issue
any Good pack of three rgb fans below 50$?
So I got a custom loop cooling system. I’m looking into changing the coolant because I’m just not a fan of the color I got. It’s thermaltake’s pastel white. I’m looking for something more vibrant, to just pop. 1) does anyone have any recommendations of brands of coolant to look into? This’ll be the first change I’ve done for it so I’m not sure what all is decent. 2) any recommendations on how to change liquid/flush the system? It’s CPU cooling only, so there’s not much tubing, and it’s soft tubing so I can bend it as needed, I’m just not sure of how to approach on doing so
good day i am looking into a better cooler for my ryzen 7 2700X on my 570 plus wifi mobo currently i am using a stock cooler any suggestions
@left tree scythe makes good quiet fans that are decent price
@marble phoenix what budget?
Cheap: hyper 212, gammaxx 400
Less cheap but below $50: scythe mugen5 or be quiet shadow rock 3
a friend suggested the Corsair h100i
i don’t mind price as long as it does the job good
I mean if you want to attend over $100 for a cooler that is complete overkill you can do that too
Arctic freezer ii only aio
Thermaltake Pure 12 ARGB 5V Motherboard Sync/Analog Controller TT Premium Edition 16.8 Million Colors 9 Addressable LEDs 120mm Hydraulic Bearing PWM Case/Radiator Fan, 3 Pack CL-F079-PL12SW-A https://www.amazon.com/dp/B07MVY3N55/ref=cm_sw_r_cp_api_i_epnLFb3JTTY66
Are these fans good?
Ive been told this is a great cpu cooler, any reason not to get it? any other suggestions? https://www.amazon.com/dp/B07MJGNJB3?tag=pcpapi-20&linkCode=ogi&th=1&psc=1
I would suggest scythe mugen5 at that price, but they are pretty close
okay thanks
yo guys I got a question
should a Ryzen 9 3950X be at 60-70 degrees with an AIO with discord, file explorer, steam downloading something and chrome open? The AIO in question is a Z series NZXT 360mm, please respond as soon as possible
I also just built the system today]
Noctua NH-l9i best ITX cooler.
I would reapply the thermal paste
Yea check contact and if you left the plastic on
so, quick question, I'm 100% buying an AIO for me 6700k so I can do some OCing to try and get some more performance out of this older gem. I have a 2080S so I'm trying to get better single-core perf to reduce the bottleneck in a few games, noticeably GTA. question is, which AIO should I get? looking for a triple fan(360mm I think? I'm new to AIOs). I looked at the NZXT X-series one since I have an NZXT case already with a smart device V2 and 4 Hue 2 strips + underglow, so I was looking at it to match my RGB. I have an H710i so I'm sure I'll be able to fit something just fine. is the X73(also pretty sure it's that one) a good option?
f r e e z e r i i
also looking at getting brand new RGB fans, I'll need to buy 7 so an odd number I know, any suggestions? I looked at the LL and GL series from corsair but they're pretty expensive per fan, so I'm interested in other brands/ones that I may not have heard of that can give my build a more unique look
will have a look 1111
I think Coolermaster has some mid-priced rgb fans
Arctic freezer ii remains my only AIO suggestion.
:P
preferrably RGB on BOTH sides btw, or at least visible from both sides since the H710i doesn't really have a see-through front panel or top one, though I'm looking to mod the front to put a mesh grille in, and I'll have to buy some magnets and a sheet that I can use as a dust filter
tbh I've been sus about the random rgb fans now since I saw that review of the asiahorse rgb fans spewing oil everywhere lol
^ there's that too lmao
but buzz I'll have a look at youtube reviews as well to see how they look inside my case, I'll have 3 extra fans but oh well lmao
may have to buy the USB 2.0 hub from NZXT to get more headers on my old Z170 board
i think you can also get single of that one too
ok cool I'll keep it in mind
I heard that the antec ones were pretty cool too
I think they're antic, I don't remember lmao I need to catch up on my RGB fans
Anyone know when the Lian Li unifans are gonna be back in stock anywhere lol
I'll have a look at those too then, thanks for the help! if anyone else has suggestions and is reading this later just @ me cause I'm king at forgetting to check lmao
they have other models too:
https://smile.amazon.com/stores/page/3855F99A-BA63-443C-AB4C-7F4BC393856E?ingress=2&visitId=0368b2d8-0411-4060-a74b-e49c17bcb091&ref_=ast_bln
5-packs and 3-packs
Hey strangers of the internet, what would be the easiest way to connect 1 fan to an addressable 12v rgb header? i have everything working with Aura but my back fan is a cheap non addressable one i want to replace
I am getting confused with most fans being 5v and already having the 3 case fans taking that header
splitter
just a normal Y splitter really
and you can use that to connect to the current controller
and then get a splitter for the RGB signal or a passthrough
do the rgb fans come with the 5v rgb header portion? and i split off the mother board?
the controller looks like it may be limited to those 3 fans on the front but i honestly know very little about RGB stuff
i am just speaking about the technical side of it :)
i have bugger all idea about RGB from the control side of it :)
lol i dont even know what a RGB fan loos like out of the box as far as connections so i appreciate any info, very close to having my dream PC done
last step is this beat fan in the back getting synced
@twin urchin @maiden delta @low pumice thanks guys for the advice
what's a cheapish fan with high static pressure? I need 6 total, for under 100$. preferably black in color, with either NO rgb, clean adressable rgb, or a single color, like white
@cursive compass you have to be very careful about what you are describing. ARGB is 5v and cannot be mixed/adapted to 12v rgb. There is no such thing as 12v addressable rgb
@cursive compass you have to be very careful about what you are describing. ARGB is 5v and cannot be mixed/adapted to 12v rgb. There is no such thing as 12v addressable rgb
@twin urchin thats what im finding, what i am trying to find now is if i can run multiple fans off a 5v if i buy a splitter. Also if rgb fans come with 5v connector
12rgb is the one where every led is the same color
i cannot find what connectors look like on rgb fans to save my life
i just want aura to work
MOST argb is a 4pin with one of the middle pins blocked out
so essentially if i got a splitter for the 3 pin header and an rgb fan, i could syn em all off the one header?
THANKS. i am almost done and ugly back fan is all thats leftr
If you search for argb splitter on Amazon you should find some
I have found those, mostly just uncertain of the fans themselves and their connections, might head to best buy and pop some boxes open then find it cheaper online
MOST fans follow the standard
Corsair sometimeses doesn't
And the lian 'll uni fans don't
yeah i saw corsiar connections favoring their control box, i just need a cheap one for my exhaust fan
Also, in case it's not obvious, argb fans will have an rgb wire plus the normal fan wire
Pwm or 3 pin
yeah i know that, ive already got the power requirements sorted out, just not super smart on rgb header stuff
thansk for the infos!
So you might need a splitter for that too
ive got the splitters for power off the mother board for the 6 fans i have. I am just wantign to replace the back exhaust to match the case as a whole
@kindred knoll let me know if the plastic was still on and if the thermals are better after you reapply lol
Corsair sometimeses doesn't
@twin urchin Not sometimes. Always. They have their proprietary connectors, though you can rewire their stuff to be the standard connector or generic stuff to be compatible with iCue (if you know what you're doing)
All their fans, cases, and rgb strips that I know of that are controllable by iCue use their own connectors
Here's a guide if you're interested in Corsair RGB modding: https://www.reddit.com/user/Faquarl_of_Samarkand/comments/i0vq34/custom_corsair_rgb_striprgb_mod_guide_unbroken/
I went with a splitter for the 5v connecter and a single deep cool rgb fan that has a standard 3 pin rgb control
now if only i could get the stuoid 3080 FE rgb to save during restarts ide be set
my cooler master hyper 212 isnt lighting up & isnt showing up on RGB Fusion 2.0 (I have a Gigabyte X570 Aorus Elite mobo). Does anyone know how to fix this?
@crude kestrel I have that same issue with my Asus X570 Tuf Gaming Wifi and a Wraith Prism RGB Cooler, but only my mobo and vga show up on the Aura Sync software.
hello guys, so i have lian li liancool II mesh and want to upgrade my cpu cooler to noctua nh-d15. does it fit?
i have 2x16gb gskill trident z rgb
it should
does it still have space and not too closer with tempered glass?
@obsidian sun the case has clearance for up to 176mm
the NH-d15 is 165mm so gives you about 11mm of wiggler room
when it comes to your ram, you can move the fan up to fit over the ram modules
@obsidian sun the case has clearance for up to 176mm
@woeful spoke ok, so when i move the fan up to fit over the ram modules stiil fit right?
it should @obsidian sun
@obsidian sun check your ram's module height.
NH-D15 is actually fairly tight when it comes to ram below the fan
Diagram here:
Trident z rgb, the non-DC version, has a 45mm module height
(32mm+11mm=43mm. 43mm<45mm)
If you were really concerned about ram clearance, I'd grab a NH-D15s, which doesn't have a second fan.
@analog surge the cpu cooler rgb runs on a different software since it's made by coolmaster
You have to plug it into a USB header to get that to sync
➤RGB SOFTWARE- https://bit.ly/335daUP
➤FIRST VIDEO- https://youtu.be/15gEMcyotvM
This video is about how to setup and control the RGB on the AMD Wraith Prism Cooler. There are 2 lighting zones and both cables do something different. DON'T use both cables at the same time. Wat...
Watch this video it explains it in detail
@crude kestrel have you plugged in the rgb header?
because if it isn't lighting up...
there might be a rgb header you haven't plugged in
I mean they'll get lights from the RGB header I just don't think it'll be addressable and it just includes the fan not the other effects
Anyone have experience with the lian li uni sl120s?
If you were really concerned about ram clearance, I'd grab a NH-D15s, which doesn't have a second fan.
@low pumice thanks mate. I think i will pick bigger size case then. Any recomendation pc case that have nice airflow? For now phanteks p500a
Also another option - I use the U12S - it's not as beefy as a NH-D15. Unless you're doing significant overclocks it does a great job.
It doesn't overhang RAM so you can put whatever you want in there.
Can also add a second fan to that if necessary
Any recommendations for fans that will somewhat match the stock TD500 mesh fans?
ok
Is it possible to put af120 or 140 fans on the nh d15
you mean AF12 or AF14?
So does the thermal paste go into the reservoir cause its in there
and idk what do do now, the screen is all blue and there's white stuff going down the circuit thingy
So basically you want to put more thermal paste
on the circuit thingy
40 tubes minimum
Ya
Makes sure the thermal paste is tooth paste it has better preformance
what are the 40 mm tubes for. Putting more paste in there. OH OH OH WAIT i know, i have to fill the whole thing with it with the tubes. like put the paste in the tubes into the pc
Make sure your gpu is in the ram slot for better cooling
Yup make sure the radiator does plug up and your all good😌
Cooolio
And if you throw your entire pc into a pool you will never need to worry about cooling
@low pumice i'd put white led afs on to match the build, I didn't expect there to be a performance difference
I have a interesting problem with my retro pc build, I either have bad bearings in my old white led case fans I use to illuminate the case.
Or I have loose screw rolling around under my Z97's mobo armor covering that I've tried to shake out from time to time.
I am having trouble imagining how those two things could even sound remotely the same
random fan vibrations under load in the 1st case, the mobo is a used Mark S Sabertooth in the 2nd case where I might have inherited his/her lost seating screw.
Good amd cpu cooler for 3800x slight overclocking?
no such thing as an amd cpu
keep that in mind
but a 280-360m rad will keep your cpu cool even when oc
depends on what color you want and do you want rgb fans
ok
for overclocking?
i would say get a Noctua NH-D15 or a be quiet! Dark Rock Pro 4
they both are massive air coolers however
and you can get the Noctua one in black
Dang I didn’t know cpu coolers were like $100
air coolers aren't 100 usually
but those are the best air coolers
and you said you were doing overclocking, which air cooling can't really cool that much
both of them preform better than some aios though
then you can't cool it with an aio and a cooler at that price won't be able to cool your cpu if it overclocks
@forest thistle for under $50 you are looking at Scythe Mugen 5 or fuma 2, Be Quiet Shadow rock 3, Cooler Master Hyper212, or Deepcool Gammaxx 40 (or some name like that)
they should be able to handle slight overclocks on that CPU
all should be under $50, except maybe the Fuma2 which should be under $60
@snow pine I mean, there's a reason why we love Noctua as a company, they make amazing products.
@forest thistle arctic freezer ii 240 or 280 is a pretty good bang for the buck for its excellent performance
A good amount of the cooling on the heatsink comes from dem fans
@snow pine I mean, there's a reason why we love Noctua as a company, they make amazing products.
@low pumice yasss
if only they made white fans though ffs
no
white and rgb fans
The reason they're king is because they don't make rgb
i saw somewhere BeQuiet is going to make a white version of the Shadow Rock 3
white fans are annoying to make
@low pumice isn't it the same process as chromax black fans though?
and they've been promising white fans for over a year now lmao
I should say, non-beige is annoying to make for them
@blissful plank I'm pretty sure they have a complete separate process for other colored fans
damn really?
hell I thought they had someone else make it for them, I'd have to check again
@blissful plank yea I think they have a separate process
ah
but stil
still*
it's been over 2 years now since they announced chromax white fans
you think they would have found a way by then
think about how long they refine things
they took 4 years to make the NF-A12x25
it took 2 years for them to get chromax out
jesus
mhmm
Alright fair enough
anyone know how to set case fan curves based on gpu temps? speedfan isn't working for me
gammax 400
@low pumice If i were to install say just 3 basic case fans, it would be okay to just plug each one into the mobo cs fan 1, cs fan 2, cs fan 3 headers right? from there would the motherboard automatically control the speeds I'm assuming based on the temp?
Or would it just run them all on full blast the whole time?
Hello can you help me I just AIO cooler from corsair and the AIO bump cord is in the AIO Bump socket thing on the Motherboard but i cant start up the pc with out plugging a case fan into the CPU Fan socket thing but its so so load
Yes they are in the commander pro
But if i dont put a fan cord into the cup fan socket it will start up
the commander pro a fan control hub?
would it be possible to plug them into the CPU Fan header? I'm guessing they're RGB
yeah that has a different connector probably
Liquid Cooling always seems more complicated to me that's why i kinda just wanna stick to Air lol
you'd think the mobo would control the speed and reduce the noise level
based on cpu temp
yea in bios? or no
same with the pump
I'm no expert but yeah probably it would be controlled somewhere in the bios
you'd expect it to be automatic
Good, I was low key afraid I'd plug them in and they'd just go full blast all the time
lmao
@pulsar comet to start off, commander pro should have a 4pin pwm fan cable that you can just plug into the CPU_Fan header
second, you can disable the no CPU_Fan warning in bios if necessary
third, there's usually a dedicated Pump_Fan header for the pump
@burnt goblet another question for the NA-FC1, so, stumbled on the specs page, does the rated 3a on this change anything with the fans theoretically supported? And how does the controller having the ability of both 5v and 12v fans work?
re: number of fans: it all depends on the draw from the specific fans
Should i adjust my fan layout? Currently it is 3 intake in the front and 2 exhaust on top and 1 exhaust in back.
that sounds balanced enough
Alright thanks
Is my water pump on my Corsair rgb pro xt supposed to run at full speed all the time
@rapid fox have you gone into Bios and set fan curves or letting it run default?
@rapid fox if you're running it on a header that doesn't have a 'water pump' setting, you want to run it at full speed to make sure it's getting the correct voltage
@final crescent @ocean flume thank you
often they run full speed all the time anyway
Question for CPU coolers. How much difference in temp does a single tower cooler do compared to a dual tower ?
Depends
in theory a dual tower can do more
@elfin compass everything depends on the model
but it depends on how well made each one is
A 20$ gammaxx400 can outperform crappy dual tower coolers
But there's no competition when you throw in like a NH-D15 for the dual tower cooler
So what you really want to look at is your budget, and then look at the models available at the budget, and compare them. @elfin compass
Usually best at each price would be ~20$ gammaxx400, 50$ Mugen 5 rev b, 60$ Scythe ninja 5/fuma 2, 90$ NH-D15/DRP4
also need to make sure your case has clearance for the tower cooler
but in most cases there shouldn't be a problem
@twin urchin for some god damn reason it's a problem for a ton cases >:(
Like P400a
No fit big bois like D15, D15s, U14, DRP4, etc.
going to buy this its $60 off
for $60 off thats a pretty good deal
$100 for this cooler, im not building my pc for 2 months but just cause its this much off ima cop
Is front rad better than top rad? And how should the fan configurations in the NZXT H710i work with 7 120mm fans and a 360mm rad?
Such as what exhaust and what goes in.
@cinder heron either is fine
for front or back
for the second question
I would put the rad on the front
and fill out the other 4 on the top and one on the back
@distant kernel thanks, for 3 intake with the rad. What configs should the other 4 with the 3 on top and 1 on back be? Should they all be exhaust or some intake?
Is the Cooler Master MasterFan MF120R a reliable fan?
I can find a pack of 3 for $55
Eh the rgb quality's not too important
I just wanna be sure they won't die super quick on me
@low pumice Thanks for the info! Looking through some of those options, I'll have to skip out on the Noctua/DRP4. Case clearance appears to be a possible issue.
:)
Anyone here using third party RGB fans on an NZXT Z73 or X73 that you can recommend?
do i need a cooler?
or should i be fine with the base ryzen 5 one? not gonna be doing overclocking and if i do not much
?
no need to @ anyone @jade fox
oh sorry
ask your question(s) and people will answer when/if they have the time/knowledge :)
All good
about his cooler
h100i is the cooler I use
which one
works amazing on keep cpu cool
i have the h100i xt RGB
h100i plat rgb
oh
I already had rgb in my case so i didnt really need the platinum one
really good cooler
ugh my wifi is being really slow
i have a question. i cant get an Aio bc it cant fit and i have 3 front mounted fans. Should i get 3 more fans for exhaust?
im not going to overclock so a stock cooler should be fine as a temporary placeholder for the cpu cooler
@burnt goblet wait Naed, adding new case fans instead of upgrading cpu cooler as a long term solution..?
Am I understanding this wrong?
@low pumice I think Naed was refering to the CPU cooler being a stock one instead of a AIO
Not the case fans
ah kk
Will Lian Li's Uni Fan SL120 case fans ever going back into stock?
@proper fulcrum how are we supposed to know :P
Will Lian Li's
Uni Fan SL120case fans ever going back into stock?
@proper fulcrum HEY BACK OFF
THE SECOND THEY BACK I'M BUYING
...
YOU BETTER NOT EVEN LOOK AT A PRODUCT PAGE OF IT
ummm no need to treat me like that for asking a question... but ok.. whatever...
ik joking lol
@proper fulcrum dw kekw
they in stock at microcenter
but only the singlepacks
online, or in store only
cause the fact they work with fewer cables is just awesome, and is a must in my eyes
in store only...
which sucks, cause I live over 300 miles away from the closest micro center stores
@ornate zinc what you using it with?
D15 is godly for performance, just should check compatibility because it's CHONK
what the
what is that psu parametric selection lol
@ornate zinc might want to use this instead for the PSU parametric selection. Better PSUs, larger selection.
https://pcpartpicker.com/user/Mr1111/saved/ry3RvK
and I think you'd have a better time with a NH-D15s
the one without a second fan
Because TD500 mesh is tight with max height, and you can't move the second fan up to let ram fit.
and uh
be careful with that SSD selection
@ornate zinc might want to use this instead for the PSU parametric selection. Better PSUs, larger selection.
https://pcpartpicker.com/user/Mr1111/saved/ry3RvK
@low pumice Ok
What monitor should I get for the list
you looking for 1080p or 1440p?
1440p
@low pumice the point was: The stock cooler IS decent enough to use long term. Yes, there are better coolers ofc there is:) But thinking that AIO is actually needed? .... just no. :)
@burnt goblet gotcha I misunderstood that, since I thought the question was about the adding 3 case fans
anyone got those Lian LI connector fans?
Is there anyway to check an aio without installing it in a system to make sure it work?
@maiden delta just plug the pump into a header for a pump
Alright, thanks
as in, you dont have to physically install it in the case
because what you are primarily interested in is: "does the pump run?"
and you should be able to both hear and feel that
Yes, makes sense
Ok I have a fail question for the experts, where on earth do I find a 4 pin 5v replacement for a Asus duct fan?
What's more ideal a splitter cable or a fan hub? I'm leaning towards a splitter since I hear many hubs will just run everything on full
Ebay
anyone know of some good rgb fans
Just go custom loop.
@radiant pebble CoolerMaster Master fan MF120 Halo
Lots of airflow, quiet, and beautiful.
@radiant pebble https://m.youtube.com/watch?v=NCcgCJx9xlg
Find what you need at Micro Center: https://rebrand.ly/z42abwh
Custom PC Builder / Configurator – https://rebrand.ly/f2gdb6p
PC Components: https://rebrand.ly/td8xfl3
Have one of Micro Center’s techs build your PC: https://rebrand.ly/rnyto0c
Here is a direct link to the fans ...
I watched his video and tried out the brand and is pretty happy with it, I got the pwm moonlight ones in my pc
He links the fans in the description to Amazon
This might seem like a weird question @burnt goblet but say if i ran a few fan splitters off my mobo, and had like 4 case fans running what kind of wattage draw would i expect from that?
depends on the fans
someone please help
if i want to overclock
and i buy a corsair radiator cooler
do i have to have my pc water cooled for it to work
uhhh
if you get one of the AiO coolers, it will be watercooled
assuming you mean the H100/115/150
@hushed flare
yeah
or even H80
instead of the corsair one
like for that does my pc need to be water cooled?
or do i need water for it?
you mean do you have to add water?
no
everything is included
hence the common name All-in-One (AiO) for that kind of cooler
so i can just slap it on the cpu and install fans in the radiator
uh, thats up to you
https://www.amazon.com/dp/B01N40656Z?tag=pcbuilds101-20&th=1 would you guys recommend these fans?
i don't know about those specific ones, but arctic is a reputable brand
uphere has some nice ones aswell
is the Cooler Master MASTERLIQUID ML240L RGB V2 65.59 CFM Liquid CPU Cooler good for its price
cooling a 12 core prosser
not overclocked
its not a bad deal and it can cool that cpu no problem
Well if you take the radiator and cost of fans into account compared to an air cooler and fans it's not to far off
Depending on the air cooler and the fans
how much would it cost to fully water cool a 3080 and a ryzen 9 5900x?
@low pumice https://www.techpowerup.com/274136/arctic-announces-the-liquid-freezer-ii-420-aio-liquid-cpu-cooler
:D
Is the arctic liquid freezer ii 240 better than the noctua nh-d15?
They are similar priced (chromax.black) so idk which to get
@low pumice
depends entirely on your needs
i personally prefer air cooling
(for my own personal rigs)
My cpu is gonna be the r7 5800x or maybe the r9 5900x
reviews
wait for reviews of the zen3 chips
we dont know enough about how the respond to temp yet
Ok
Online reviews say that the arctic barely beats the nh-d15
So imma just go with nh-d15
Even NH-D15 might be overkill for that, depending on your overclocking/silence needs
NH-D15 is overkill unless you’re overclocking but honestly it’s great anyway
No reason you can’t keep your cpu cooler
NH-D15 is great
because you can keep swapping to new platforms
because Noctua gives free upgrade brackets
https://noctua.at/en/support/mounting-and-upgrade-kits
We provide mounting upgrades for Noctua CPU coolers free of charge, so if you would like to continue using your Noctua cooler on a new socket, we will send you a new mounting kit at no additional cost. For ordering our mounting kits, a proof of purchase (photo, scan or screens...
is 37.3dB loud for a case fan?
@azure crown i meant for case fans specifically, not in general
be quiet! Pure Wings 2
A friend recommended this if I wanted to swap out the stock cooler, is there something around the same price that is better or is this good
Scythe mugen 5, or be quiet shadow rock 3
Is the dark rock pro 4 overpriced?
Mugen5 is 1$ less than what he linked to

