First Build: Siboor Voron 0.2 Kit

[rancid totem]

Back in early March, I learned about the Voron ecosystem after I came across a video on Reddit showcasing the 247zero. And I was hooked on the idea of a small ABS-printing machine that is quite affordable. So here we go.

Ordered on Taobao during a sale, sea shipping to Malaysia took a bit more than 2 weeks. The package arrived on Monday (24th) but I totally forgot that I need a soldering iron stand to safely park the tool which became an excuse for procrastination.

First Build: Siboor Voron 0.2 Kit

[vagrant egret]

Let me know if you run across any issues because i just ordered me a v0 kit from siboor

[grave ridge]

Welcome!

[rancid totem]

80% of frame assembled.

[vagrant egret]

They come with genuine hiwin rails for all axis?

[crimson aurora]

They come with siboor branded rails.
The extrusions they use are also a different shape.

[vagrant egret]

Oh it looked like it said hiwin

[rancid totem]

color looks like hiwin but it says siboor

x axis rail carriage has a different color

[vagrant egret]

Let me know how the build goes and if you have any complications because I have a kit in the way @rancid totem

[crimson aurora]

As I mentioned previously, the profile of the siboor extrusions can cause issues.

Siboor extrusions is blue, LDO/standard in green.

Just be careful which nut carriers you print.

[vagrant egret]

@crimson aurora do you have a stl for the correct ones?

[crimson aurora]

@vagrant egret I suggest you start your own build log so we can answer questions there, instead of hijacking Raidens build log

[rancid totem]

https://www.printables.com/model/650959-siboor-voron-02r1-no-drop-m3
I used this for no drop nuts mod.

[vagrant egret]

Thank you

[rancid totem]

Frame done. Gave up trying to perfectly square the frame: worst case I'll just go get the Fysetc frame alignment tool.

Next step will be preparing all the heat set inserts. Progress is slow being a weekend shift warrior...

[crimson aurora]

It's not a race.
One step at a time; you'll get there 🙂

[rancid totem]

Z lead screw done. X axis next...

[rancid totem]

X axis done. Belts next...

[rancid totem]

Assembled the top hat first... ran out of m3 nuts halfway and had to get more from a nearby hardware store. Preloaded too many... Now gotta figure out how to do the belts.

[rancid totem]

😂 don goofed and inserted the hot bed extension wire crimp terminals into the connector before passing it through the drag chain... welp, snipped the connector off, ordered crimp tool (probably takes a week to ship, and I don't think I'll reach wiring phase before it arrives), and gotta redo it.

[vagrant egret]

If you turned it on were you fans working? @rancid totem

[rancid totem]

still waiting for crimp tool to get delivered...

[vagrant egret]

👍🏻

[rancid totem]

by the way did you have to crimp the hot bed LED wires?

[vagrant egret]

The led on the kirigami bed?

[rancid totem]

yeah

[vagrant egret]

I believe it was precrimped but you had to put the connector on

[rancid totem]

i wonder if i should just skip the LEDs as i'm not a fan of fancy RGB stuff

[vagrant egret]

I didn’t do the led for the toolhead as I forgot and didn’t want to solder of crimp anything

[rancid totem]

anyways yeah, need that crimp tool to do the wiring (and i haven't even installed the belt because procrastination + being weekend shift warrior with mid-week breaks). not a big setback, need the tool for the next project (self source 2.4) anyways...

[vagrant egret]

The build was fun and took me over 10 hours but I’m still yet to get my first print due to firmware issues and the fans not working.

Good luck

[latent iron]

What fans are not working for you? Hotend and part cooling fan? In case the siboor kit is also using the V0 umbilical, there is a common issue where the fans need to be depinned and have the polarity swapped. Not sure if this is a problem for the siboor kits