klipper_kalico_help

Klipper Update Issues (display?) 9 messages

Nov 22, 2025, 5:00 AM Solved Clicked update bttn

printer wont start up i get this error 114 messages

Nov 21, 2025, 3:34 PM Error messages

Can't access mainsail on Voron 0.1 anymore 10 messages

Nov 21, 2025, 11:12 AM Installation Solved Connectivity Config

Unknown pinchip name probe 5 messages

Nov 20, 2025, 1:20 PM Solved

pi 5 won`t work 6 messages

Nov 20, 2025, 9:29 AM Installation Flashing

pressed the update button 24 messages

Nov 19, 2025, 3:50 PM Installation Error messages Flashing

Z offset 32 messages

Nov 19, 2025, 4:07 AM Macros Meshing & probing

Servo not fully turned 180 degree 2 messages

Nov 19, 2025, 3:38 AM Installation Macros Config

Voron 2.4 stops printing in the middle of print, no error showing 25 messages

Nov 18, 2025, 3:52 PM Error messages

Timer to close 9 messages

Nov 16, 2025, 10:35 PM Error messages

MCU Shutdown error 16 messages

Nov 16, 2025, 9:44 PM Error messages

New MP5 19 messages

Nov 16, 2025, 6:03 PM Error messages

Flashing toolhead board issues 6 messages

Nov 15, 2025, 2:26 AM Flashing

Klipper reports: ERROR Unknown pin chip name 'Probe' 18 messages

Nov 15, 2025, 2:02 AM Config

help tuning the "A-better-print_start-macro" 2 messages

Nov 14, 2025, 7:59 PM Solved Macros

Trouble with X and Y retract errors 10 messages

Nov 14, 2025, 1:29 PM Installation Error messages Config Meshing & probing

I am getting the two warnings when compiling for MCU and I am not quite sure how to clear them 9 messages

Nov 14, 2025, 2:43 AM Error messages Solved Flashing

Error with numpy on input shaping 31 messages

Nov 12, 2025, 10:10 PM Error messages Config

Malformed command 'SET_ENCLOSURE_FAN S51' 35 messages

Nov 11, 2025, 10:47 PM Solved Macros

mcu shutdown, timer too close 8 messages

Nov 11, 2025, 7:05 PM Connectivity

Any idea on why a printer would just straight up ignore a command? 4 messages

Nov 11, 2025, 3:04 AM Config

Klipper not working anymore after update, get_response() takes from 3 to 5 positional arguments but 49 messages

Nov 9, 2025, 9:20 PM Error messages Solved

Led strip not working 7 messages

Nov 9, 2025, 8:31 PM Config

Error after updating 11 messages

Nov 9, 2025, 6:04 PM Error messages Clicked update bttn Solved

mcu not communicating with raspberry pi on new setup 77 messages

Nov 9, 2025, 7:36 AM Installation Solved

Help configuring Sensorless Homing and Beacon 32 messages

Nov 7, 2025, 1:49 PM Config

Help with initial build and *.cfg M8P, Nitehawk, TAP 9 messages

Nov 7, 2025, 12:02 AM Installation Error messages Connectivity Config Solved

Dirty Klipper 25 messages

Nov 6, 2025, 3:44 AM Error messages Solved

Can't see my Nitehawk MCU 7 messages

Nov 5, 2025, 9:09 PM Flashing

UART harness for power + USB serial = ??? 4 messages

Nov 5, 2025, 5:50 AM Connectivity

[SOLVED] Sensorless Crashing At All Thresholds 80 messages

Nov 3, 2025, 8:42 PM Installation Solved

sensorless homing not working, SGTHRS dont matter 8 messages

Nov 2, 2025, 10:53 AM Solved Config

Raspberry Pi 3B problems 2 messages

Nov 2, 2025, 12:19 AM Error messages

"MCU 'mcu' shutdown: Timer too close" when running ShakeTune 6 messages

Nov 1, 2025, 8:08 PM Error messages

A good method to manage klipper from iPad 3 messages

Nov 1, 2025, 5:05 AM Macros Config

Klipper reports: ERROR Section 'update_manager z_calibration' is not a valid config section 17 messages

Oct 31, 2025, 3:25 PM Solved

Home Z before starting next object - cartographer 6 messages

Oct 30, 2025, 3:57 PM Macros Config Meshing & probing

klippy.log shows config after all [includes]? 9 messages

Oct 30, 2025, 2:51 PM Config

'mcu'' shutdown: timer too close 3 messages

Oct 30, 2025, 4:04 AM Error messages Macros

mcu ebb usb / Lost communication with MCU 'EBB' Once the underlying issue is corrected... 23 messages

Oct 28, 2025, 9:38 PM Connectivity

Filament macros 10 messages

Oct 28, 2025, 9:27 AM Solved Macros Config

use ADXL345 (Nitehawk SB) for Testing resonances in Z Axis 5 messages

Oct 27, 2025, 9:16 AM Installation Config

PT1000 config with MAX31865 chip on EBB36 v1.2 51 messages

Oct 24, 2025, 6:54 PM Installation Config

Option 'pin' in section 'probe' must be specified 14 messages

Oct 24, 2025, 4:16 PM Error messages Solved

RPIcam install help 8 messages

Oct 24, 2025, 2:39 PM Camera

Error after Klipper-Update 5 messages

Oct 24, 2025, 1:34 PM Error messages Config Meshing & probing

X endstop triggered all the time after not using the printer for a week 5 messages

Oct 24, 2025, 7:47 AM Connectivity Solved Config

Need help with error 2 messages

Oct 24, 2025, 1:41 AM Error messages

Beacon connection issues on first layer causing klipper shutdown 36 messages

Oct 23, 2025, 11:53 PM Connectivity

Klipper error "Thermocouple reader fault" 12 messages

Oct 23, 2025, 5:30 PM Error messages