klipper_kalico_help

ADC out of Range - shutdown 10 messages

Nov 20, 2024, 5:05 PM Error messages

Two printers on one pi 4 messages

Nov 19, 2024, 8:27 PM Installation Connectivity Config

Verify_Heater error 3 messages

Nov 19, 2024, 3:41 AM Config

INDUCTION PROBE ISSUES 8 messages

Nov 18, 2024, 11:27 PM Solved Meshing & probing

Object exclusion not accurate 7 messages

Nov 18, 2024, 5:48 PM Config

Yet another MCU EBBCan shutdown. Timer too close.. 3 messages

Nov 18, 2024, 7:43 AM Error messages

Dual Z stepper configured but one driver get hot while the other room temp? 5 messages

Nov 16, 2024, 8:33 PM Config

Firmware configuration for BTT Octopus Pro 1.1 33 messages

Nov 16, 2024, 8:16 PM Solved Config Flashing

is async gcode_shell_command possible? 3 messages

Nov 16, 2024, 7:28 PM Macros Config

Tap Config 3 messages

Nov 15, 2024, 11:00 PM Solved Config

2.4 Config, Drivers 15 messages

Nov 15, 2024, 8:35 PM Config

Variable Input Shaper 2 messages

Nov 15, 2024, 1:44 PM Macros Config

How to add shutdown pi to the v0 display ? 18 messages

Nov 15, 2024, 1:16 PM Klipperscreen

Unable to write tmc spi 'stepper_x' register GLOBALSCALER 9 messages

Nov 14, 2024, 12:13 AM Error messages

Print_end minimum height 2 messages

Nov 13, 2024, 9:41 PM Macros

SET_VELOCITY_LIMIT 4 messages

Nov 13, 2024, 3:31 PM Error messages Config Solved

Why does my Trident forget it is homed? 2 messages

Nov 13, 2024, 12:40 PM Solved Config Meshing & probing

Kraken extruder skipping. 16 messages

Nov 13, 2024, 10:00 AM Solved Config

Hello. Can someone please help understand why my MCU shuts down when it detects a runout? 2 messages

Nov 13, 2024, 3:53 AM Error messages

Error connecting to MCU 6 messages

Nov 13, 2024, 2:40 AM Connectivity Error messages

looking for good macros for V2 2 messages

Nov 12, 2024, 8:34 PM Macros

no extrusion during prints 7 messages

Nov 12, 2024, 5:34 PM Macros

fysetc 2 messages

Nov 12, 2024, 5:23 PM Flashing

Problemes with Klippian 2 messages

Nov 12, 2024, 12:44 PM Macros

MCU unable to connect.... 2 messages

Nov 12, 2024, 10:30 AM Error messages Solved

Initial setup of 2.3 Extruder, EBB CAN 2209. 8 messages

Nov 11, 2024, 5:54 PM Solved Config

Lost connection after install klipperscreen with network manager 5 messages

Nov 11, 2024, 6:38 AM Installation Solved Klipperscreen

4WD with Y-boosting 2 messages

Nov 10, 2024, 8:10 PM Error messages Solved

Dynamic Bed Temp for QGL 3 messages

Nov 10, 2024, 6:55 PM Macros Config Meshing & probing

Issue with reboot 2 messages

Nov 10, 2024, 8:39 AM Connectivity Config

PRINT_START macro not grabbing hotend/bed temp from Orcaslicer 3 messages

Nov 9, 2024, 12:54 PM Solved Macros

Can't get Neopixels to work on BTT Octopus 1.1 8 messages

Nov 9, 2024, 5:18 AM Solved Config

btt pi 2 and skr pico 2 messages

Nov 9, 2024, 12:30 AM Installation Solved Flashing

seting up more than one extruder? 2 messages

Nov 8, 2024, 3:02 AM Installation Config Meshing & probing

"Target board uses Smoothieware bootloader" option not shown 5 messages

Nov 8, 2024, 3:00 AM Solved Flashing

Migrating History Database from LMDB to SQL 2 messages

Nov 8, 2024, 2:32 AM Installation Solved

MCU configuration randomly gives an error. 11 messages

Nov 8, 2024, 1:48 AM Connectivity Error messages Config

LDO picoumbilical random disconnects 9 messages

Nov 7, 2024, 9:20 PM Connectivity

BTT eddy, temperature issues, need advice for a macro 3 messages

Nov 7, 2024, 1:48 PM Macros Config

issues flashing m8p 21 messages

Nov 6, 2024, 8:10 PM Flashing

CANBus issues, pt1000 reading 20 over appropriate value 36 messages

Nov 6, 2024, 5:52 AM Installation Solved Connectivity

MCU unable to connect 14 messages

Nov 5, 2024, 6:44 PM Flashing

Constant MCU shutdowns during prints. 14 messages

Nov 5, 2024, 11:26 AM Error messages Solved

Klipperscreen "unable to load panel print" 5 messages

Nov 4, 2024, 7:13 PM Solved Klipperscreen

Why dos mine not have the E stop at the bottom left like the example? 4 messages

Nov 3, 2024, 5:01 PM Solved Klipperscreen

[SOLVED] Flashing Spider 2.2 Failing 22 messages

Nov 2, 2024, 2:27 AM Solved Flashing

"MCU 'CB1': Unable to connect" 14 messages

Nov 2, 2024, 2:20 AM Installation Solved Connectivity

IDM sensor keeps getting MCU disconnect - usb5-port1: disabled by hub (EMI?), re-enabling... 3 messages

Nov 1, 2024, 9:44 PM Connectivity Error messages

Klipper updated - now not able to boot the machine 7 messages

Nov 1, 2024, 6:09 PM Error messages Config

Klipper no space left 8 GB CM4 2 messages

Nov 1, 2024, 10:40 AM Installation Config