klipper_kalico_help

Non CAN extra MCU connection to CAN bridge? 3 messages

Jan 31, 2025, 10:09 AM Connectivity Solved Config

github backup timed out 19 messages

Jan 31, 2025, 8:15 AM Error messages Macros Solved

"Must home axis first" on sensorless homing if bed mesh exists and motors have been off 5 messages

Jan 30, 2025, 7:50 PM Meshing & probing

Timer too close 45 messages

Jan 30, 2025, 3:43 PM Error messages

Various frustrating wifi, firmware and klipper issues. 8 messages

Jan 30, 2025, 2:02 PM Connectivity

trying to install moonrake through akiuh 225 messages

Jan 29, 2025, 2:41 AM Installation

Klipper [extruder] section not respecting new rotation_distance value? 2 messages

Jan 29, 2025, 1:54 AM Solved Config

14:34:25 Error evaluating 'gcode_macro BED_MESH_CALIBRATE:gcode': jinja2.exceptions.UndefinedError: 29 messages

Jan 28, 2025, 7:55 PM Meshing & probing

Print Start help 5 messages

Jan 27, 2025, 1:21 AM Config

Sensorless Homing Issues [AWD] 106 messages

Jan 26, 2025, 9:45 PM Config

Everything says corrupted but printer works fine? 53 messages

Jan 25, 2025, 2:04 AM Error messages

Voron 2.4 wont initialize 13 messages

Jan 24, 2025, 1:23 PM Connectivity Installation Error messages

Sensorless homing with 2 Y motors on Switchwire 29 messages

Jan 24, 2025, 3:00 AM Solved Config

BTT Pi becoming unresponsive mid print 3 messages

Jan 24, 2025, 1:17 AM Connectivity

fans - Running cooling 2 Fans on ebb36 34 messages

Jan 23, 2025, 1:31 AM Config

simultaneous MMUs 2 messages

Jan 22, 2025, 9:06 PM Config

Problem with activated smart Filament senor. 2 messages

Jan 22, 2025, 5:13 PM Macros

Mesh 4 messages

Jan 22, 2025, 3:36 AM Meshing & probing

Probe pin not valid? 34 messages

Jan 21, 2025, 3:24 AM Meshing & probing

Unable to Connect to CM4? 23 messages

Jan 20, 2025, 9:12 PM Error messages Solved

Unable to connect to Moonraker after update. 6 messages

Jan 20, 2025, 2:51 PM Connectivity

Used KIAUH to update, now I can't connect to host. 5 messages

Jan 20, 2025, 4:44 AM Connectivity

Klipper Shutdown 4 messages

Jan 19, 2025, 12:57 PM Error messages

klippy host software issue 23 messages

Jan 19, 2025, 6:34 AM Installation Error messages Connectivity Solved Flashing

Klipper Can not connect to Moonraker! 4 messages

Jan 19, 2025, 2:20 AM Error messages Solved

Klipper Ignoring PAUSE macro during print 22 messages

Jan 18, 2025, 9:56 PM Macros

Bed Meshing Adaptive not working 12 messages

Jan 18, 2025, 2:20 AM Solved Meshing & probing

Bed PID tune error 9 messages

Jan 17, 2025, 9:35 AM Error messages Solved

Klicky and z calibration 2 messages

Jan 17, 2025, 3:46 AM Macros Config

cartographer usb wont connect for some reason 2 messages

Jan 16, 2025, 11:40 PM Installation Solved

Offset after printing home 13 messages

Jan 15, 2025, 2:33 AM Macros

Recently unable to connect to printer via SSH 15 messages

Jan 14, 2025, 11:29 PM Connectivity Solved

Flashing Fystec r4 board 5 messages

Jan 14, 2025, 10:21 PM Flashing

Cant resume prints 2 messages

Jan 14, 2025, 9:21 PM Solved Macros Config

Printer not following sequence outlined in config 11 messages

Jan 14, 2025, 8:13 PM Solved Macros Config

CM5: Crash after firmware restart 77 messages

Jan 14, 2025, 9:13 AM Connectivity Error messages Klipperscreen Solved

Print history only shows 100 prints 2 messages

Jan 13, 2025, 7:06 PM Installation

Switching from CB1 to CM5 14 messages

Jan 13, 2025, 2:48 PM Installation Error messages Solved

PRINT_START variable assignment 3 messages

Jan 12, 2025, 10:51 PM Solved Macros

Automatic bed levelling? 5 messages

Jan 12, 2025, 4:01 PM Solved Config

Error: MCU unable to connect 10 messages

Jan 12, 2025, 10:55 AM Connectivity

Trouble installing S2DW accelerometer 6 messages

Jan 10, 2025, 2:37 PM Error messages

How to safely shutdown entire system? 9 messages

Jan 10, 2025, 1:42 PM Solved Macros

ADC Out of range 44 messages

Jan 10, 2025, 7:00 AM Error messages

MCU 'mcu' shutdown: Timer too close, I've tried many things 11 messages

Jan 10, 2025, 12:53 AM Error messages

Enable pin at startup to start case light 2 messages

Jan 8, 2025, 9:22 PM Solved Config

Error "The value 'filament_motion_sensor' is not valid for SENSOR" in Klipper 13 messages

Jan 8, 2025, 8:02 PM Macros

Movement Issues 12 messages

Jan 7, 2025, 1:28 AM Config

Unable to connect thermistor 60 messages

Jan 6, 2025, 3:56 AM Error messages Solved

Delayed gcode macro 3 messages

Jan 5, 2025, 1:43 PM Macros Config