klipper_kalico_help

Can not update MCU 'mcu' config as it is shutdown 9 messages

Feb 17, 2025, 11:09 PM Error messages Solved

Do I need mailsail.cfg? 2 messages

Feb 17, 2025, 7:21 PM Macros

Stealthburner status LED 2 messages

Feb 16, 2025, 1:19 AM Installation Solved Macros Config

Exclude object moving to excluded object anyway 2 messages

Feb 15, 2025, 6:44 PM Macros

Z offset acts the same despite changing it in the config 4 messages

Feb 14, 2025, 7:46 PM Meshing & probing

Z offset 2 messages

Feb 14, 2025, 6:26 PM Config

'make menuconfig' query 5 messages

Feb 13, 2025, 12:41 PM Flashing

Chamber thermistor and exhaust fan config 7 messages

Feb 12, 2025, 7:42 PM Solved Macros Config

MCU unable to connect after update 4 messages

Feb 12, 2025, 3:06 PM Error messages

Stuck on the Initializing screen after a network upgrade 2 messages

Feb 11, 2025, 2:18 AM Connectivity Error messages Config

UNO as additional MCU. Flashes successfully, but gives error: "Unknown command: tmcuart_send" 15 messages

Feb 9, 2025, 4:25 PM Error messages Flashing

How to solve this 14 messages

Feb 9, 2025, 3:04 PM Error messages

moonraker not connecting 5 messages

Feb 9, 2025, 3:09 AM Solved Config

Extruder not heating at expected rate 7 messages

Feb 9, 2025, 12:49 AM Error messages

Host Name Resolution Over VPN 8 messages

Feb 8, 2025, 9:31 PM Connectivity Config

Does this config look right? I'm using TMC 5160T pro v1.0 drivers on an Octopus pro v1.0 16 messages

Feb 8, 2025, 8:57 PM Solved Config

I installed shake tune last night and now Moonraker says it cant connect? 26 messages

Feb 8, 2025, 5:41 PM Connectivity

wrong flash mcu [SOLVED] 31 messages

Feb 7, 2025, 4:27 PM Solved Flashing

MCU Protocol ERROR 4 messages

Feb 6, 2025, 8:45 PM Error messages Clicked update bttn Flashing

BED MESH: Move of of range.... 21 messages

Feb 6, 2025, 3:43 AM Error messages Macros Config Solved

TMC 'stepper_x' reports error: GSTAT: 00000001 reset=1(Reset) 2 messages

Feb 5, 2025, 6:58 PM Error messages

AngryCam stop working after v12 update 11 messages

Feb 5, 2025, 4:11 PM Solved Camera

New thermistor 10 messages

Feb 4, 2025, 3:13 PM Config

print bed size printer.cfg 19 messages

Feb 4, 2025, 12:04 PM Config

Katapult errors when building 13 messages

Feb 4, 2025, 2:18 AM Error messages Solved Flashing

help! My printer stopped working and iv had to do a full restart from scratch and having issues. 63 messages

Feb 2, 2025, 5:17 PM Error messages Solved

Z_Tilt_Adjust adjusing wrong motor 8 messages

Feb 2, 2025, 4:39 PM Macros

Homing X turns motors on but then no motor movement 27 messages

Feb 2, 2025, 10:13 AM Solved Config

MCU mcu shutdown timer is too close 2 messages

Feb 2, 2025, 9:53 AM Error messages

Printer I just purchased isn't booting and I don't know why 54 messages

Feb 2, 2025, 4:47 AM Meshing & probing

zstandard issue? 5 messages

Feb 2, 2025, 1:23 AM Solved Clicked update bttn

Help i cant connect to the raspberrypi? 50 messages

Feb 2, 2025, 12:16 AM Connectivity Error messages

DropEffect neXtG 14 messages

Feb 1, 2025, 3:23 PM Solved

Losing connection to SHH, Klipper 16 messages

Feb 1, 2025, 7:46 AM Connectivity

Non CAN extra MCU connection to CAN bridge? 3 messages

Jan 31, 2025, 10:09 AM Connectivity Solved Config

github backup timed out 19 messages

Jan 31, 2025, 8:15 AM Error messages Macros Solved

"Must home axis first" on sensorless homing if bed mesh exists and motors have been off 5 messages

Jan 30, 2025, 7:50 PM Meshing & probing

Timer too close 45 messages

Jan 30, 2025, 3:43 PM Error messages

Various frustrating wifi, firmware and klipper issues. 8 messages

Jan 30, 2025, 2:02 PM Connectivity

trying to install moonrake through akiuh 225 messages

Jan 29, 2025, 2:41 AM Installation

Klipper [extruder] section not respecting new rotation_distance value? 2 messages

Jan 29, 2025, 1:54 AM Solved Config

14:34:25 Error evaluating 'gcode_macro BED_MESH_CALIBRATE:gcode': jinja2.exceptions.UndefinedError: 29 messages

Jan 28, 2025, 7:55 PM Meshing & probing

Print Start help 5 messages

Jan 27, 2025, 1:21 AM Config

Sensorless Homing Issues [AWD] 106 messages

Jan 26, 2025, 9:45 PM Config

Everything says corrupted but printer works fine? 53 messages

Jan 25, 2025, 2:04 AM Error messages

Voron 2.4 wont initialize 13 messages

Jan 24, 2025, 1:23 PM Connectivity Installation Error messages

Sensorless homing with 2 Y motors on Switchwire 29 messages

Jan 24, 2025, 3:00 AM Solved Config

BTT Pi becoming unresponsive mid print 3 messages

Jan 24, 2025, 1:17 AM Connectivity

fans - Running cooling 2 Fans on ebb36 34 messages

Jan 23, 2025, 1:31 AM Config

simultaneous MMUs 2 messages

Jan 22, 2025, 9:06 PM Config