voron_2_help_forum_public

BTT canbus install on klipper 26 messages

Feb 19, 2024, 12:28 PM Kits/parts advice Initial setup

Galileo 2 random under extruding 13 messages

Feb 19, 2024, 12:24 PM Tuning Mechanical Configuration

Gantry shifts when homed to Z 15 messages

Feb 19, 2024, 12:58 AM Tuning Mechanical Z Offset QGL Configuration

NiteHawk-SB Neopixels Not working 19 messages

Feb 18, 2024, 11:12 PM Solved Electronics & wiring Configuration

left side of 2.4 gantry wants to sag out of random 16 messages

Feb 18, 2024, 10:49 PM Mechanical Solved

Bad print quality 3 messages

Feb 18, 2024, 9:55 AM First print

Shake Tune Input shaper not making graph. 45 messages

Feb 17, 2024, 8:50 PM Tuning Configuration

Z-axis steppers going "brrrr " during printing, x/y movement 32 messages

Feb 17, 2024, 7:05 PM Tuning

Unable to get "downstream" XXL Disco on a stick to light 13 messages

Feb 17, 2024, 6:38 PM Electronics & wiring Configuration

dead board? 6 messages

Feb 17, 2024, 10:18 AM Mechanical

Weird artifacts after "upgrading" to Rapido UHF Hotend 41 messages

Feb 17, 2024, 9:23 AM Tuning

ssh fails, dozen reimages 19 messages

Feb 16, 2024, 10:44 PM Electronics & wiring

Wiring motor NEMA14 with EBB2209 2 messages

Feb 16, 2024, 9:21 PM Electronics & wiring

Extruder issues 2 messages

Feb 16, 2024, 2:16 PM Mechanical

Print defects 3 messages

Feb 15, 2024, 9:23 PM Tuning First print

Problems with heatcreep above cold zone on revo 46 messages

Feb 15, 2024, 9:16 AM Mechanical Electronics & wiring

Problems with perimeters in printing...? Not sure why... 18 messages

Feb 15, 2024, 7:58 AM Configuration

Premade Wiring loom has odd connections for the mainboard, where would these plug into? 8 messages

Feb 15, 2024, 4:37 AM Electronics & wiring

filament sensor 21 messages

Feb 14, 2024, 10:26 PM Initial setup

Klicky Probe as Endstop. 64 messages

Feb 14, 2024, 6:23 AM Z Offset Initial setup Configuration

hotend not heating at expected rate 6 messages

Feb 14, 2024, 5:21 AM Printer shutdown

How do I find renamed stls. Specifically looking for what superceded the old plug_panel.stl 8 messages

Feb 14, 2024, 4:14 AM Kits/parts advice

neopixel turns off at layer 4 3 messages

Feb 14, 2024, 12:15 AM Solved Electronics & wiring

Help diagnosing a weird clicking / rubbing(?) noise 5 messages

Feb 13, 2024, 10:53 PM Mechanical

Home_xy_position in printer.cfg file has no effect on homing sequence 10 messages

Feb 13, 2024, 7:52 PM Configuration

BTT Octopus Pro v1.1 canbus 49 messages

Feb 13, 2024, 3:41 PM Electronics & wiring

Dragon HF low max VF 3 messages

Feb 13, 2024, 6:48 AM Tuning

Pressure Advance Calibration 4 messages

Feb 12, 2024, 11:18 PM Tuning

Bambu Labs Hotend In StealthBurner. 7 messages

Feb 12, 2024, 8:25 PM Configuration

Layer Shifts 71 messages

Feb 12, 2024, 6:47 PM Tuning Mechanical Solved

vibration problem 63 messages

Feb 12, 2024, 5:56 PM Tuning Mechanical Initial setup

Gantry stiff when hot 7 messages

Feb 12, 2024, 4:10 PM Mechanical

bad bed mesh 7 messages

Feb 12, 2024, 9:12 AM Bed mesh issue

hardware - Z_End_Stop, Magnetic Beds, Quad Gantry Level 40 messages

Feb 12, 2024, 5:06 AM Initial setup Configuration

Klipper Updated, now mcu not connecting 10 messages

Feb 11, 2024, 8:55 PM Printer shutdown Solved Electronics & wiring Configuration

Z offset completely broken 8 messages

Feb 11, 2024, 1:39 PM Z Offset

Z offset not reliable after every print 5 messages

Feb 11, 2024, 10:54 AM Mechanical First layer

Print Issues 101 messages

Feb 11, 2024, 7:46 AM Tuning

Flash SKR 1.3 56 messages

Feb 11, 2024, 4:30 AM Configuration

/dev/serial/by-id : no such file or directory 4 messages

Feb 10, 2024, 11:48 PM Electronics & wiring

Very simple macro does not work 6 messages

Feb 10, 2024, 2:34 PM Bed mesh issue Configuration QGL

heater bed heats to a certain point then temp drops then starts climbing again 2 messages

Feb 10, 2024, 1:41 PM Electronics & wiring

new build - tool head slams into left gantry 3 messages

Feb 10, 2024, 5:49 AM Configuration

Unhandled exception during run PLEASE HELP 4 messages

Feb 10, 2024, 1:44 AM Mechanical Solved Configuration

is there a limit to the weight on top of a 2.4? 3 messages

Feb 9, 2024, 1:35 PM Mechanical

Diagnosing layer shift occurring mid-print 12 messages

Feb 9, 2024, 2:45 AM Mechanical Electronics & wiring

Problem with bed heater 31 messages

Feb 8, 2024, 10:44 PM Mechanical Printer shutdown Electronics & wiring

Uneven Z axis movement 3 messages

Feb 8, 2024, 7:13 PM Mechanical Z Offset QGL

Quad Gantry Level Moving Off Print Bed 22 messages

Feb 8, 2024, 3:22 PM QGL

bed mesh not compensating 3 messages

Feb 8, 2024, 2:25 AM Bed mesh issue First layer Solved