voron_2_help_forum_public

Error when turning on V2.4 9 messages

Aug 18, 2024, 5:42 PM Printer shutdown Electronics & wiring

Skipping steps in bed-leveling 5 messages

Aug 18, 2024, 1:45 PM Bed mesh issue

probe triggered 6 messages

Aug 17, 2024, 11:27 PM Electronics & wiring Configuration

Klicky Problems 6 messages

Aug 17, 2024, 9:42 PM Configuration

Somethings off... 35 messages

Aug 17, 2024, 7:43 PM Tuning Solved

Good first later then under extrusion for the rest of the print 7 messages

Aug 17, 2024, 7:28 PM Tuning

Lost a rail ball from the carriage 9 messages

Aug 17, 2024, 5:50 PM Mechanical Solved

Katapult Update Voron 2.4 76 messages

Aug 17, 2024, 2:40 PM Initial setup

Y homing suddenly not working 3 messages

Aug 17, 2024, 2:24 AM Mechanical Solved Electronics & wiring Configuration

Bed heater not working properly anymore 84 messages

Aug 17, 2024, 1:47 AM Printer shutdown Electronics & wiring

Nozzle touch probe for voron 2.4? 4 messages

Aug 15, 2024, 8:58 PM Z Offset Kits/parts advice First layer

Heater extruder not heating at expected rate 30 messages

Aug 15, 2024, 6:46 PM Printer shutdown Electronics & wiring

Lost communication with MCU 'nhk' Nitehawk keeps disconnecting. 24 messages

Aug 15, 2024, 2:38 PM Printer shutdown Solved Electronics & wiring Configuration

where to get a MGN9 center alignment guide 11 messages

Aug 15, 2024, 1:06 PM Kits/parts advice Initial setup

Unable to read tmc uart 'stepper_x' register IFCNT 2 messages

Aug 15, 2024, 10:36 AM Initial setup

extruded stops pushing filament mid print 10 messages

Aug 14, 2024, 3:21 PM Tuning Mechanical Configuration

Installation of Z belts and belt tension 3 messages

Aug 13, 2024, 4:34 PM Mechanical Initial setup Solved

exhaust fan wire routing 3 messages

Aug 13, 2024, 2:19 PM Kits/parts advice Electronics & wiring

Burnt Inductive Probe slot 55 messages

Aug 13, 2024, 1:33 AM Electronics & wiring

Any tips for flattening out this bed mesh? 6 messages

Aug 12, 2024, 9:34 PM Bed mesh issue

Tilted gantry after printing finished 31 messages

Aug 12, 2024, 5:41 PM Mechanical Solved

Help! octopus isn't recognized from pi. 32 messages

Aug 12, 2024, 10:03 AM Initial setup Solved Electronics & wiring Configuration

inductive probe issues 8 messages

Aug 12, 2024, 9:18 AM Electronics & wiring QGL

More layer shift issues. 3 messages

Aug 11, 2024, 11:27 PM Mechanical

Toolhead Endstop 2 messages

Aug 11, 2024, 2:05 PM Kits/parts advice Solved Electronics & wiring

probe problems voron r2.4 6 messages

Aug 11, 2024, 7:32 AM Bed mesh issue

MCU 'EBBCan' shutdown: Not a valid ADC pin 17 messages

Aug 11, 2024, 3:51 AM Printer shutdown Electronics & wiring

Looking for help telling klipper what pins to use for my PT1000 thermistor? 7 messages

Aug 10, 2024, 6:12 PM Electronics & wiring Configuration

Manta M8P Installing USB-CAN-Bridge Klipper 43 messages

Aug 10, 2024, 1:34 PM Configuration

Voron 2.4 cabling without kit 5 messages

Aug 10, 2024, 8:48 AM Electronics & wiring

steel wire 9 messages

Aug 9, 2024, 3:27 PM Kits/parts advice

Voron2 degradation 3 messages

Aug 8, 2024, 11:06 PM Configuration

Looking for someone who could help me instal CanBoot/Katapult.... I've been at it for 2 months. 109 messages

Aug 8, 2024, 7:33 PM Tuning Initial setup Electronics & wiring

Controller fan not working. 5 messages

Aug 8, 2024, 5:38 PM Initial setup Electronics & wiring

GQL is perfect, but first layer is grinding in a specific corner [SOLVED] 7 messages

Aug 7, 2024, 6:09 PM Mechanical Z Offset First layer Tap QGL

Bed Level - First Print 9 messages

Aug 7, 2024, 2:11 PM Bed mesh issue Z Offset Initial setup First layer Configuration

Z axis moving at different rates 27 messages

Aug 6, 2024, 1:47 PM Mechanical Configuration

Inconsistent Z-offset 35 messages

Aug 6, 2024, 8:45 AM Z Offset Mechanical QGL

P Dragon hotend falls out/is not firmly in place on stealthburner 31 messages

Aug 6, 2024, 1:53 AM Solved

First layer and other issues 3 messages

Aug 5, 2024, 7:03 PM Tuning Z Offset Bed mesh issue

sensorless homing Octopus pro V1 TMC 5160t Bigtreetech 4 messages

Aug 5, 2024, 4:38 PM Electronics & wiring Configuration

voron 2.4 wiring (formbot kit) and firmware 4 messages

Aug 5, 2024, 2:43 PM Initial setup Solved Electronics & wiring

weird extrusion clicks on stealthburner 38 messages

Aug 5, 2024, 10:04 AM Mechanical Solved

Abnormal Hotend Temperature Results: 5 messages

Aug 5, 2024, 12:25 AM Electronics & wiring Configuration

Does anybody have any experience with kits from this Aliexpress seller? 5 messages

Aug 4, 2024, 10:07 PM Kits/parts advice Solved

Communication timeout during homing 71 messages

Aug 4, 2024, 12:10 PM Bed mesh issue Electronics & wiring Initial setup Solved Configuration

hard to mount z belt covers with hammer head T-nuts 2 messages

Aug 4, 2024, 2:51 AM Kits/parts advice

Sensorless trouble 2 messages

Aug 3, 2024, 7:45 PM Electronics & wiring

Possible bug in the sensorless homing? 4 messages

Aug 3, 2024, 3:32 PM Electronics & wiring Configuration

Can Bus Mainboard replacement not setting up 23 messages

Aug 3, 2024, 2:30 PM Electronics & wiring Mechanical Kits/parts advice Initial setup Solved