voron_2_help_forum_public

Printer stopped working after Wi-Fi change. 10 messages

Jan 11, 2025, 9:15 PM Initial setup Printer shutdown

Curved/Bend corner in x/y plane 2 messages

Jan 11, 2025, 4:50 PM Tuning Mechanical Solved

Missing configuration 11 messages

Jan 11, 2025, 10:40 AM First print

Filament Coming Out While Heating ( a lot ) 86 messages

Jan 10, 2025, 1:11 PM Tuning First layer Solved

Voron 2.4 find a mistake in the wiring 22 messages

Jan 10, 2025, 11:08 AM Tap Initial setup Solved Electronics & wiring

Which one first? Flow Rate ( Extrusion Multiplier ) or Pressure Advance? 11 messages

Jan 9, 2025, 11:45 PM Tuning Solved

Stealthburner Sailfish stops printing 44 messages

Jan 9, 2025, 3:39 PM Mechanical

[SOLVED] Diagonal Movement on QGL 2 messages

Jan 9, 2025, 4:08 AM Mechanical Solved Electronics & wiring

little bit of play on the left side 26 messages

Jan 9, 2025, 1:56 AM Mechanical

Probe Z-Offset vs Offset? 20 messages

Jan 9, 2025, 1:55 AM Z Offset Solved

Stl for part 2 messages

Jan 9, 2025, 1:39 AM Mechanical Kits/parts advice Electronics & wiring

Z Motor locking up 4 messages

Jan 9, 2025, 1:02 AM Mechanical Solved Electronics & wiring

Base plate Hole Spacing 3 messages

Jan 8, 2025, 4:39 AM Initial setup Electronics & wiring

Z-Motor Tensioners 3 messages

Jan 8, 2025, 3:32 AM Mechanical

Stl for part 3 messages

Jan 7, 2025, 11:38 PM Kits/parts advice Mechanical Solved

Questions about print scale accuracy 37 messages

Jan 7, 2025, 10:08 PM Tuning Mechanical Solved Configuration

What parts to print? 3 messages

Jan 7, 2025, 1:00 PM Kits/parts advice

0.4 to 0.6 nozzle change 3 messages

Jan 7, 2025, 7:03 AM Tuning Solved Configuration

Is there better assembly manual for the electronics for the 2.4r2? 8 messages

Jan 7, 2025, 2:24 AM Solved Electronics & wiring

Uneven First Layer Issue 154 messages

Jan 6, 2025, 4:25 AM First layer Solved

Where is the stl for the end stop? 2 messages

Jan 6, 2025, 1:40 AM Z Offset Kits/parts advice Solved

How to fix/troubleshoot possible z-drift issue 7 messages

Jan 5, 2025, 7:58 PM Mechanical Electronics & wiring

Voron 2.4 Printing List 21 messages

Jan 5, 2025, 7:09 PM Kits/parts advice Solved

Looking for hotend upgrade suggestions 3 messages

Jan 5, 2025, 7:08 PM Kits/parts advice

Motors not responding to any move commands 6 messages

Jan 5, 2025, 2:34 PM Initial setup Solved

Uneven first layer 19 messages

Jan 5, 2025, 9:01 AM Tuning First layer Configuration

Need help for nozzle stuck during printing 7 messages

Jan 5, 2025, 4:23 AM Kits/parts advice Printer shutdown Configuration

Nevermore and chamber temp help needed 13 messages

Jan 5, 2025, 2:45 AM Solved Configuration

Canbus setup with a toolhead board and an mmu board? 5 messages

Jan 4, 2025, 11:31 PM Solved Electronics & wiring

Canbus upgrade on 2.4 4 messages

Jan 4, 2025, 8:53 PM Electronics & wiring Configuration

z end stop triggered x:open y:open z:TRIGGERED 15 messages

Jan 4, 2025, 5:54 AM Electronics & wiring Z Offset Initial setup Solved Configuration

Printed parts 2 messages

Jan 4, 2025, 4:15 AM Kits/parts advice Solved

Hotend fan won't start with my canbus 2209/2240 20 messages

Jan 4, 2025, 3:54 AM Initial setup Electronics & wiring

Hotend Heating Issue 6 messages

Jan 4, 2025, 3:09 AM Solved Electronics & wiring

Front Right Z motor runs at power on until klipper starts. 20 messages

Jan 4, 2025, 1:49 AM Solved Electronics & wiring QGL

Issues with LDO Nitehawk SB toolhead board 6 messages

Jan 3, 2025, 10:10 PM Printer shutdown Electronics & wiring

Layer shifting over 120mm gantry height 8 messages

Jan 3, 2025, 1:21 AM Mechanical Solved

Printer(s) stop extruding mid print 53 messages

Jan 3, 2025, 1:00 AM Tuning Configuration

Mains voltage wiring 5 messages

Jan 2, 2025, 2:14 PM Solved Electronics & wiring

Major Printer Overhaul 8 messages

Jan 1, 2025, 3:39 AM Electronics & wiring Kits/parts advice Configuration

Switchwire BedMesh 3 messages

Jan 1, 2025, 2:47 AM Bed mesh issue

MCU 'mcu' shutdown: Thermocouple reader fault 2 messages

Dec 31, 2024, 11:07 PM Printer shutdown Solved Electronics & wiring

Heat Creep Paranoia 18 messages

Dec 31, 2024, 10:51 PM Tuning Solved

Changed to Klippain, having config issues and need help. 8 messages

Dec 31, 2024, 3:45 AM Solved Configuration

Spool drag causing under extrusion? 5 messages

Dec 31, 2024, 3:30 AM Z Offset First layer Solved

Heater Pad Starting To Fall Off 5 messages

Dec 30, 2024, 8:57 PM Kits/parts advice

Pulley and Motion 13 messages

Dec 30, 2024, 8:41 PM Mechanical

z axis dimensional accuracy substantially short 10 messages

Dec 30, 2024, 5:39 PM Tuning Initial setup Solved Configuration

Voron 2.4, klipper. mcu 'mcu': Unable to connect 4 messages

Dec 30, 2024, 1:45 PM Initial setup Solved

very bad first layer 49 messages

Dec 30, 2024, 11:11 AM First layer Solved