voron_2_help_forum_public
mcu unable to connect message
Initial setup
Solved
Configuration
Octopus Flash
Initial setup
Configuration
Beacon contact Calibration
First layer
dragonburner
Kits/parts advice
New build, inconsistent z offset.
Tuning
Z Offset
First layer
Solved
Bed adhesion issues
First layer
Solved
Printer shuts down 13 hours into a 14 hour print
Printer shutdown
Voron Setup assistance
Initial setup
Beacon Bed Mesh Incorrect
Bed mesh issue
Extrusion cutting out
Mechanical
Solved
Layer shifting
Tuning
Mechanical
Electronics & wiring
Configuration
Auto bed leveling compensation
Bed mesh issue
Z Offset
First layer
Solved
Configuration
Frame extrusion prints to cut your own.
Kits/parts advice
Mechanical
Solved
Back right z-axis clunking.
Mechanical
Solved
Electronics & wiring
Umbilical
Mechanical
Kits/parts advice
Solved
Electronics & wiring
Wavy heightmap. LDO Voron kit 2.4 350 kit
Bed mesh issue
Kits/parts advice
Mechanical
First layer
Configuration
Unable to get proper bed leveling/z offset
Z Offset
First layer
QGL
Small movements of wrong axis when toolhead moves
Mechanical
Initial setup
Solved
Configuration
Voron 2.4 - Unknown pin chip name 'probe'
Solved
Configuration
Recommended belt brand and tension
Kits/parts advice
Mechanical
Solved
I can't for the life of me equalize tension in my belts
Tuning
Mechanical
Solved
Klipper Parsing error
Initial setup
Solved
Configuration
EBB 2209 USB connection lost during print
Electronics & wiring
these t nuts drive me crazy, am i missing something?
Mechanical
Solved
Resonance? Extruder?
Tuning
Mechanical
Help required. TMC 'stepper_z1' reports error: DRV_STATUS: c0180020
Printer shutdown
Solved
Can manually heat the bed but doesn’t work when I start a print
Solved
Electronics & wiring
Klipper config error MCU shutdown ADC out of range
Printer shutdown
Initial setup
Electronics & wiring
Configuration
Klipper config for Voron 2.4 v2 with EBB SB2209 rp2040, Chaotic Tap v2 and BBT Octopus Pro v1.1
Initial setup
Wires routing
Mechanical
Solved
Electronics & wiring
tmc uart 'stepper_z' register IFCNT
Solved
Electronics & wiring
Configuration
corners lifting nearly every print with abs.
Initial setup
Any reason not to use calipers to square the gantry?
Tuning
Mechanical
What to watch out for on a preowned v2.4
Tuning
Electronics & wiring
Initial setup
Solved
Configuration
Voron 2.4 Stealthburner with Tap and SB2209 Can bus and Orbiter 1.5
Tap
Kits/parts advice
Solved
Build help. GT2 9mm belt lengths
Kits/parts advice
Mechanical
Initial setup
Minor warping on Printed Parts
Kits/parts advice
Solved
Unable to heat bed
Solved
Electronics & wiring
X homing issues.
Tuning
Now have a Voron 2.4 but it's not very fast on Orca
Tuning
Initial setup
Configuration
X axis hall effect Mount
Kits/parts advice
Mechanical
Solved
Electronics & wiring
voron 2.4 2r printed parts
Kits/parts advice
Solved
x movement
Mechanical
Kits/parts advice
V2.4r2 New Build from LDO Kit with surface defects
Tuning
Mechanical
First print
Solved
LDO Rev A Voron kit.
Initial setup
Solved
Voron 2.4 with mainsailos not booting
Printer shutdown
Solved
Strange bed heating
Electronics & wiring
Configuration
Video
Mechanical
Switching to Nitehawk 36 USB Tool board - Should I stay with Stealth Burner, or...? LDO 2.4 350mm
Kits/parts advice
Solved
Belt a/b
Tuning
Mechanical
Solved