voron_2_help_forum_public
Replacing toolhead and wiring, need advice on what to pick
Kits/parts advice
Back left corner doesn't move with the rest when moving the gantry near the top
Mechanical
Motor wiring
Initial setup
Electronics & wiring
Heater can't maintain temp over 200 or so.
Mechanical
Solved
(YANQ) Can Remote Desktop Be Run on PC linking to Raspberry Pi???
Solved
Configuration
hotend+ shutdown
Electronics & wiring
Did I use the wrong pulleys?
Mechanical
Gantry isn't square
Solved
Cooling Fan speed(PWM) problem
Electronics & wiring
Configuration
Trident 250 - X axis layer shift
Tuning
Solved
Configuration
TMC2209 Error
Printer shutdown
z axis skipped
Z Offset
Configuration
Loud motors
Tuning
Mechanical
Solved
Electronics & wiring
Possible Sensorless issue
Mechanical
BTT 4.3 display LDO Voron 2.4 rev D stays blank white
Kits/parts advice
Initial setup
Electronics & wiring
Configuration
(YANQ) - How many have upgraded all firmware and all is AOK?
Solved
Configuration
Lower tool head bolts done line up with brass inserts? SOLVED
Mechanical
Kits/parts advice
(YANQ) - Yet Another Noob Question - Can Z Endstop Switch and Virtual Be Enabled At Same Time?
Configuration
Consistent layer shift at 0.6mm
Mechanical
Solved
USB SD CARD Mount Raspberry PI Ver 4B - Clone Image Help
Initial setup
Configuration
config file help
Initial setup
Solved
Vibration in sweeping corner and circles.
Tuning
Mechanical
Solved
Buzzing stepper_x and stepper_y results in nothing
Initial setup
Electronics & wiring
Sensorless homing issues only Y
Mechanical
Electronics & wiring
Chamber thermistor
Solved
Electronics & wiring
Switched to Kalico, now moonraker can't connect to klipper
Initial setup
Solved
Shortcircuit CAN problems
Electronics & wiring
heater bed stopped heating
Printer shutdown
Electronics & wiring
screeching noise when moving left motor
Mechanical
Stepper Motor Wiring
Electronics & wiring
EBB36 Time too close issue
Printer shutdown
Electronics & wiring
Voron 2.4 with rapid burner, Orbiter 2.5, hartk pcb and dragchain
Mechanical
Solved
Eddy Duo
Tuning
Z Offset
Initial setup
Configuration
20x20 Aluminium Extrusion
Kits/parts advice
Solved
Want my 2.4 print better quality need help
Tuning
Mechanical
Kits/parts advice
220v heated bed on 120v mains
Kits/parts advice
Solved
Unable to read tmc uart 'stepper_z3' register IFCNT
Printer shutdown
Print has a line/split at a specific height.
Tuning
Mechanical
Z Offset
Solved
Print at wrong coordinate
Initial setup
First print
Configuration
Latch for Filametrix with ECAS not working
Kits/parts advice
Mechanical
Chamber thermistor 2.4 rev c.
Kits/parts advice
Z stop cable vs Z endstop cable
Kits/parts advice
de-racking issues 3mm of play
Mechanical
Solved
Strange Resonance Issues
Tuning
Getting a 2nd hand Voron 2.4 up and running.
Kits/parts advice
Initial setup
Electronics & wiring
Configuration
Motor starts to wonder off on its own during SHAPER_CALIBRATE
Mechanical
Initial setup
Electronics & wiring
Need some help on 2.4 rev c build
Kits/parts advice
Can't find Config in Fluidd
Configuration
PID_CALIBRATE shutdown
Printer shutdown
Initial setup
Electronics & wiring
V2.4 "hangs" at the end of a print
Printer shutdown
Solved
Electronics & wiring
Configuration