voron_2_help_forum_public

Hotend choices? 8 messages

Aug 3, 2025, 3:25 AM Kits/parts advice

Suddenly losing temp and "verify_heater" error 7 messages

Aug 3, 2025, 12:54 AM Solved Electronics & wiring

SB2040 toolhead fan always on? 43 messages

Aug 2, 2025, 4:35 PM Initial setup Solved

Small camera that won’t broke down from heat 8 messages

Aug 2, 2025, 4:26 PM Kits/parts advice Electronics & wiring

Gantry Squaring Struggles 3 messages

Aug 2, 2025, 2:50 PM Initial setup Solved

Offline Spaghetti detection? 6 messages

Aug 2, 2025, 2:57 AM Configuration

Unable to bind socket to can0 4 messages

Aug 1, 2025, 11:53 PM Initial setup Solved

CANBUS PID Tuning Hotend Failure 12 messages

Aug 1, 2025, 11:46 PM Initial setup Solved Electronics & wiring

Voron 2.4 Formbot kit, What cable for Protective Earth 3 messages

Aug 1, 2025, 8:50 PM Kits/parts advice Electronics & wiring

BTT Octopus 1.1 Katapult firmware problem 16 messages

Aug 1, 2025, 6:15 AM Configuration

Belts rubbing on cable covers 5 messages

Jul 31, 2025, 11:29 PM Mechanical Solved

shealthburner clockwork 2 over extruding 51 messages

Jul 31, 2025, 2:35 PM Tuning Solved Configuration

Canbus accessory ports idea? 5 messages

Jul 31, 2025, 11:57 AM Electronics & wiring

Gantry alignment issue (new build) 13 messages

Jul 31, 2025, 5:39 AM Initial setup Solved

Is my activated carbon good for printer? I did the test and here’s the result. 8 messages

Jul 31, 2025, 2:55 AM Kits/parts advice

Omron probe polarity? 3 messages

Jul 30, 2025, 10:17 PM Solved Electronics & wiring

Voron 2.4 - Unstable chamber temps 11 messages

Jul 30, 2025, 9:17 PM Tuning Mechanical Solved

Maximum A/B tension 4 messages

Jul 30, 2025, 8:19 PM Mechanical Solved

Stealthburner Hot end Fan Wont Turn Off 2 messages

Jul 30, 2025, 6:27 PM Tuning Electronics & wiring

QGL is doing this, Initial startup. 41 messages

Jul 30, 2025, 3:45 PM Initial setup Solved QGL

X movement weird noises on high speed 38 messages

Jul 30, 2025, 12:37 PM Mechanical Solved

A good skirt fan that’s not Noctua 24 messages

Jul 30, 2025, 1:34 AM Kits/parts advice Electronics & wiring

Stepper polarity? 11 messages

Jul 29, 2025, 11:19 PM Solved Electronics & wiring

Looking for ideas - Rebuild Printer with 2.4 Gantry 7 messages

Jul 29, 2025, 6:30 PM Kits/parts advice Mechanical Solved

Shaper input problems with 6mm awd 5 messages

Jul 29, 2025, 5:00 PM Tuning Kits/parts advice Mechanical

The third skirt fan placement for v2.4 4 messages

Jul 29, 2025, 12:24 PM Kits/parts advice Mechanical Solved Electronics & wiring

how do i connect sb2209/rp2040 to octopus v1.1 6 messages

Jul 29, 2025, 10:47 AM Kits/parts advice Solved Electronics & wiring

Mastering LW PLA (pre foamed) 9 messages

Jul 29, 2025, 5:32 AM Mechanical

Weird Z motors unsync during a print 18 messages

Jul 28, 2025, 12:54 PM Bed mesh issue Mechanical Z Offset Solved QGL

Input shaper behaving weirdly 2 messages

Jul 27, 2025, 11:06 AM Tuning Solved

Fan selections/Troubleshooting tips for exhaust 8 messages

Jul 26, 2025, 3:26 PM Kits/parts advice Mechanical

AB belt tension. 4 messages

Jul 26, 2025, 11:46 AM Tuning Mechanical Solved

Klipper reports: ERROROption 'aliases' in section 'board_pins' must have 2 elements 8 messages

Jul 26, 2025, 8:57 AM Solved Configuration

Printed part not matching up with rail 38 messages

Jul 26, 2025, 1:17 AM Kits/parts advice Initial setup Solved

Wavy finish on the top layer 7 messages

Jul 25, 2025, 10:03 PM Tuning First print Initial setup Solved

Holes are undersized? 5 messages

Jul 25, 2025, 9:49 PM Mechanical

klicky location in config 4 messages

Jul 25, 2025, 8:10 PM Solved

Ticking noise on x-axis moves coming from toolhead. 33 messages

Jul 25, 2025, 5:58 PM Mechanical Solved

Benchy has missing PLA at the bow point 9 messages

Jul 25, 2025, 3:21 PM First print Solved

I'm confused by the order of operation trying to follow the LDO instructions 27 messages

Jul 25, 2025, 2:11 AM Kits/parts advice Solved Electronics & wiring

Motor wires and heat sinks 14 messages

Jul 25, 2025, 2:04 AM Kits/parts advice Solved Electronics & wiring

EBB SB2209 RP2040 hotend not heating up 19 messages

Jul 24, 2025, 2:03 PM Initial setup Solved Electronics & wiring

More questions about wiring 13 messages

Jul 24, 2025, 2:58 AM Kits/parts advice Electronics & wiring

Hotend temperature not stabilizing after upgrade 12 messages

Jul 23, 2025, 1:16 PM Tuning Mechanical Electronics & wiring Configuration

Belts moving wird when there is to much tension 55 messages

Jul 23, 2025, 12:37 AM Initial setup

Mid print - mcu 'EBBCan': Unable to connect 6 messages

Jul 22, 2025, 11:58 PM Electronics & wiring

Trying to figure out this diagram 62 messages

Jul 22, 2025, 11:38 PM Kits/parts advice

Klipper Shuts Down Due to Heater Not Heating At Expected Rates 14 messages

Jul 22, 2025, 5:19 PM Printer shutdown

Not valid ADC pin 32 messages

Jul 22, 2025, 11:28 AM Solved Electronics & wiring Configuration

Power supply switch 6 messages

Jul 22, 2025, 3:22 AM Kits/parts advice Initial setup Solved