With the fans for the bottom I’d like to use the rgb if possible
#new pc
vital wyvern
Yeah you can replace them etc, you'd just need to use the EK Hub
errant herald
Keeping the Cyberpower ones on my rad is fine I guess, so I can use two hubs in one machine?
vital wyvern
Yeah its a non issue
errant herald
Nice one ty, never used a hub before haha so it’s new to me
Never had rgb either! Lol
vital wyvern
you can either daisy chain the RGB bit of the fan without the hub and just use fan headers but its easier to use the Hub
errant herald
Okay Ty will see if I can find somewhere to put it and see if I can get it working, I am assuming since all fans including my AIO are connected to the Cyberpower on the remote control will control my AIO fans
vital wyvern
The AIO RGB is probably connected to the motherboard but you can connect it to the Hub if you wanted
errant herald
I know all the headers are full on the Cyberpower hub
vital wyvern
Yeah that uses its own Hub
errant herald
Got 4 case fans plugged in and my 3 AIO ones which as you say are prob in the motherboard
I don’t think I have a port for the EK hub
vital wyvern
The EK hub only needs 1 fan header, then 1 RGB 3 pin port, and a SATA power
errant herald
Oh lmao
My bad 😉
So new to rgb lol
Gonna see how to fit my gpu support bracket first it’s a Suprim x one looks very odd lol
vital wyvern
It just stands up in the case and you Push the Bar up to the bottom of the Gpu
Frankly it doesn't need it
errant herald
Ohh I’m use to the ones that use the things at the back and okay ty haha
signal quartz
Didn’t mean to delete the whole post
My bad just wanted to delete the last photo as it had your order number in it
errant herald
Oh sorry haha I didn’t realise
heady herald
I saw the deleting of stuff and i was confused 
errant herald
Just figuring out how to get to the psu haha, such a strange but awesome case
Just to confirm the EK hub, 3 pin mn fan goes in the hub 4 pin goes on the motherboard fan header.
2 pin in the hub and 3 pin rgb into a jrgb header on the board?
vital wyvern
Yes
errant herald
Nice one ty, just got find somewhere to mount the hub as I don’t have any spare sticky pads
vital wyvern
Ram it in a drive bay
errant herald
Good shout!
vital wyvern
Not quite literally ram it, but you get my point 
errant herald
Haha yeah, will try mount it otherwise might just have to leave it sat in there
Still trying to find out how to get at the psu lol, there’s a cover on the back panel but doesn’t want to budge as it’s hooked in at the bottom
Ah that’s the ssd tray that’s covering the psu connector
So kinda stuck atm as the case instructions doesn’t give detail how to remove it
cyan thorn
Wow that is clean whoever cable managed that is a legend
errant herald
YeH I believe so
I’ve removed the 4 screws holding it but it’s basically hooked at the bottom and it’s got a flat bit at the top that over reaches the top of the case
Instructions show this
vital wyvern
Try and get a hand behind it and slightly push, if you don't think its moving don't force it
errant herald
Him
Hmm*
Doesn’t seem anywhere for it to go
Ohhh I wonder if I need remove the other two screws and keep that other thing fixed.
Yeah! I think that’s where I went wrong
Instead of the top one
I’m in
errant herald
Not enough cable length on the fans
leaden monolithBOT
:tada: Congrats @errant herald, you levelled up to 12! :tada:
vital wyvern
if you're plugging into the Hub, you only need 1 fan header, you will for sure have some at the bottom of your motherboard
errant herald
YeH I meant fan cables reaching but I don’t even have any fan screws lol
I have some spare from previous builds. Phew lol
Gonna have one as non rgb as I fitted the fan the wrong way for cables to reach and can’t be bothered to unroutr all the other fan cables I have already put through the pc lol
That will have to do
errant herald
That’s my failed attempt lol, really couldn’t be bothered to try find how to take the case apart for the back fan and remove my cable routing for the rgb fan st the front bottom.
vital wyvern
You've set them to outtake at the bottom btw
errant herald
Yeah it’s the cables are not exactly loose so the tray won’t pull out to dip them lol
heady herald
Fix that damn RGB, its killing my OCD
errant herald
Yeah me too many
Man*
I’ll have to do it in a min lol
See if I can get some small screw drivers to get at it
vital wyvern
Looks nice, Just don't turn them up to full RPM, Unless you want to go deaf
errant herald
Just going into the bios now
errant herald
I’m gonna guess the pump is connected into the pump header
vital wyvern
That looks like Pump to me
errant herald
Yeah makes sense with this
vital wyvern
Just so you're aware you can use PUMP headers for fans, And even CPU headers for pumps
errant herald
Ah okay, d that running the correct rpm for the pump?
errant herald
Looks like the back exhaust fan must be connected to a seperate header
Oh I know what they have done,
System 3 and 2 are my fans on the side panel, so the top and back dan must be under pump
The ones under pump seem to only go to 1550
errant herald
What temp does the 4090 fans kick in on the supreme by default?
vital wyvern
55-60 in Gaming mode
errant herald
That keep fans at 70?
vital wyvern
70% yep... your choice though
errant herald
Will prob get msi afterburner and set a fan curve but a reasonable one to keep it cool, did something similar with my 3070TI
vital wyvern
I set it at 70 as mentioned and never go above 50c GPU
errant herald
Nice, for temps for 13900k what is to be expected? Currently looking at temps through msi centre but not sure if that is accurate
vital wyvern
In gaming usually around 40-65c
errant herald
On the core?
vital wyvern
In anything that maxes the CPU out, expect over 90c on the package