#Hello Kermit, thanks for your quick

1 messages · Page 1 of 1 (latest)

gleaming echo
#

does button 3 have two different events for hold and release?

sick dust
#

thanks for your support 🙂

#

Also sorry for my slow answer but i'm also new in use of discord 🙂

#

Actually button 3 have One out put use

#

it's use for play my sonos

#

I put the different nodes with output from my node TriActionHueTap

gleaming echo
#

if you put a debug node after the mqtt node hold down button 3 what event shows in the debug panel?

sick dust
#

i do it now 🙂

gleaming echo
#

create a new switch node after the mqtt node for testing and for the first case use button_3_hold and for the second use button_3_hold_release

#

you should also test if you see the button_1_press while holding down button 3

#

the device might not send out a button press is a button is being held down

sick dust
#

Well, i copy paste your flow

#

I change a 4 in 3

#

But when i hold button 3 and press button 1, the button 1 don't appear in debug 😭

gleaming echo
#

so the device might not support sending a button press when a button is being held down

sick dust
#

😦 i understand

#

there is not possiblity to bypass this?

#

My goal is. With some button i can switch on ledstrip1, then an othen button i can switch on an other ledstrip2.

#

And with the dial i can select brightness

#

With an other button i can put in mode temperature

gleaming echo
#

you could do some sort of timeout

sick dust
#

but it do this on the last ledstripi am

sick dust
gleaming echo
#

one sec

sick dust
#

i see one thing. When i hold button 3 and stay a moment on this and clic on button 1, it show me button 3 Hold release

#

But do the same thing if i clic on button 2 or 3 or 4

gleaming echo
#

logic should be if you hold down button 3 then release

#

then either press button 1 or 2 that will set the active led

#

then if you press button 3 it will turn on/off

#

in the demo it should just print out the active one

#

might need to install node-red-contrib-traffic

sick dust
#

ok

#

I have an unknow node traffic

gleaming echo
sick dust
#

Which palette i must search

gleaming echo
#

node-red-contrib-traffic

sick dust
#

🙂

gleaming echo
#

this adds a timeout if you dont press button 1 or 2 it reset the block

sick dust
#

Cool, it seams to work 🙂

#

Now i will try to adapt this in my allflow...

#

It's cool from you to take time for me. Thanks again.

#

As you see my flow is HUGE lol

#

May be i must put all my dream with this switch on a paper and come to you?

#

🙂

sick dust
#

Here is my complex Dream 🙂

#

My wife will hate me 🙂

#

and you too lol

sick dust
#

Thanks again for this clue, i will search how to put in practical this. Good help for me 🙂

#

And if you have time and also want. you have my drema in this excel file 🙂

sick dust
#

Don"t arrive in my Goal because the button are use already 😦

#

I try in the first time do This:In Mode "Intensité" if Hold Button 3 then if i clic button 1 then "ActiveLight" = credence

#

Like this if i dial left or right the brightness down up of this lamp

#

If i hold button 3 then clic button 2 in mode "Intensité" i put the ActiveLight in "HensisAll".

#

I can control "Credence" or "HensisAll" and dial left or right after toggle the light

#

But if i switch on First HensisAll, and after thaht toggle "crédence". Then if i want control EnsisAll again, i must find a way to select this want and dial without switch off then switch on.

#

Hope you understand what i mean. Thanks again for your help. May be your proposition is simply to apply but i'm a bit lost in all this :-(. Hope you will see my write and sorry for all my long text 🙂 Best regards

sick dust