#Klipper - Overheating and weird actions from stepper motors.

1 messages · Page 1 of 1 (latest)

slate blazeBOT
#
AI Help

It sounds like you may need to adjust the Vref settings for your TMC2209 drivers to ensure they are supplying the correct amount of current to each stepper motor. It's important to set the Vref correctly to prevent overheating and ensure proper motor operation.

For the extruder motor not extruding any filament and getting hot, it could be due to a clog in the hotend or issues with the extruder mechanism. Make sure the filament path is clear and the extruder gear is gripping the filament properly.

For the X axis overheating, it could be a mechanical issue such as binding or incorrect motor wiring. Check the physical movement of the X axis to see if there are any obstructions or misalignment causing excessive heat.

For the Y axis not homing and freezing when the motor current is reduced, it could be related to the Vref settings or mechanical issues such as a loose belt or pulley. Ensure the Y axis is moving smoothly and the belt tension is correct.

Make sure to double-check all wi...

WARNING: This response is AI generated and may contain errors.
uneven elbow
# 
[include mainsail.cfg]

[force_move]
enable_force_move: True

# Driver0 X Axis
[stepper_x]
step_pin: PF13
dir_pin: !PF12
enable_pin: !PF14
microsteps: 16
rotation_distance: 40
endstop_pin: PG12
position_endstop: 0
position_max: 250
homing_speed: 150

# Driver2 Y Axis
[stepper_y]
step_pin: PF11
dir_pin: !PG3
enable_pin: !PG5
microsteps: 16
rotation_distance: 40
endstop_pin: PG13
position_endstop: -35
position_max: 200
position_min: -35
homing_speed: 150

# Driver1 Z Axis
[stepper_z]
step_pin: PG0
dir_pin: PG1
enable_pin: !PF15
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
#endstop_pin: PG14
position_max: 220
homing_speed: 15

#Driver3 Extruder
[extruder]
step_pin: PG4
dir_pin: PC1
enable_pin: !PA2
microsteps: 32
rotation_distance: 4.637
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA0 # HE0
sensor_pin:  PF4 # T0
sensor_type: EPCOS 100K B57560G104F
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 280

[tmc2209 stepper_x]
uart_pin: PC4
diag_pin: PG6
run_current: 1.2
stealthchop_threshold: 0

[tmc2209 stepper_z]
uart_pin: PD11
diag_pin: PG9
run_current: 1.2
stealthchop_threshold: 0

[tmc2209 stepper_y]
uart_pin: PC6
diag_pin: PG10
run_current: 1.2
stealthchop_threshold: 0

[tmc2209 extruder]
uart_pin: PC7
run_current: 0.8
diag_pin: PG11
stealthchop_threshold: 0

# A [probe] section can be defined instead with a pin: setting identical
# to the sensor_pin: for a bltouch
[bltouch]
sensor_pin: ^PB7
control_pin: PB6
z_offset: 3.89
y_offset: -10
samples: 2
sample_retract_dist: 7

[safe_z_home]
home_xy_position: 110, 110
speed: 100
z_hop: 10
z_hop_speed: 30
# 
[bed_mesh]
speed: 120
horizontal_move_z: 10
mesh_min: 90, 30
mesh_max: 240, 170
probe_count: 5, 3

[mcu]
serial: /dev/serial/by-id/usb-Klipper_stm32h723xx_130030001251333031373837-if00
# CAN bus is also available on this board

[printer]
kinematics: cartesian
max_velocity: 200
max_accel: 100
max_z_velocity: 15
max_z_accel: 5

[heater_fan fan1]
pin: PD12

[controller_fan controller-fan]
pin: PD13

[multi_pin fans_multi_pin]
pins: PA8, PE5

[fan]
pin: multi_pin:fans_multi_pin

[heater_bed]
heater_pin: PA3
sensor_pin: PF3 # TB
sensor_type: EPCOS 100K B57560G104F
control: pid
pid_Kp: 54.027
pid_Ki: 0.770
pid_Kd: 948.182
min_temp: 0
max_temp: 130
#

I have some new motors I am gonna throw in but I dont understand why the extruder is just sitting doing nothing. When I tell klipper to extrude I can feel pulses from the motor but no movement

slate blazeBOT
#
This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

uneven elbow
#

Ive replaced the x and y motors, and changed the microstepping,

#

The main problem is still the extruder not extruding.

uneven elbow
#

Thats the main problem,

uneven elbow
#

?help

slate blazeBOT
# 
BenchyBot

BetaCommands:
  add_printer  Adds a printer to your name.
  belt_freq    Calculates target belt frequency (Hz) for correct tension base...
  belt_tension Calculates the tension (N) in a GT belt based on the measured...
  pi           
  random_thing Find a random thing from thingiverse.
  time         Used to get the current time in a timezone.
  topic        
HelpForum:
  solved       
​No Category:
  help         Shows this message

Type ?help command for more info on a command.
You can also type ?help category for more info on a category.
slate blazeBOT
#
This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.