Printer location in Florida

[true dragon]

AI Help

In a hot and humid environment like Florida, it's definitely a good idea to keep your 3D printer indoors to maintain print quality and prevent issues like filament moisture absorption. While a HEPA filter can help with controlling emissions from certain filaments, it might not be necessary for general use.

For an enclosure, you can consider building one using materials like acrylic or even constructing a DIY enclosure using plexiglass sheets, ensuring good ventilation for the printer. You can also consider adding features like a temperature monitor or a dehumidifier to help regulate the conditions inside the enclosure. You may want to prioritize ventilation and temperature control in your setup, rather than focusing solely on a HEPA filter.

If you have any specific questions or need further guidance on setting up your printer in a hot and humid environment, feel free to ask!

WARNING: This response is AI generated and may contain errors.

[worn parrot]

It will most likely be fine outdoors as long as you keep the filament in a drybox (if you do end up having issues with heatcreep you might have to move it inside down the line)

You shouldn't enclose the A1 mini because the increased temperature inside an enclosure can damage the electronics + A1 mini can only print PLA, PETG, and TPU so I wouldn't be too worried about fumes

[bleak kayak]

garage it is then🤷

[worn parrot]

I'd print in the garage and air it out for a bit after printing

You want that so PA doesn't warp no?

Nylon almost always benefits from a heated chamber

But you definitely want a active drybox to print from

It won't hurt the print quality

[true dragon]

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

[true dragon]

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.

[stray notch]

Hey man, take deep breath, sometimes people misread the question.....and sometimes the question is hard to read (either could apply)
No-one is paid to be here 😅

In any case, you should search "lack table enclosure" and see what comes up. By now, with the popularity of the a1, there should be some good sized remixes.

It really depends on whether you want to build vs buy one.
Building one requires more work but u can customise closer to what you want...

(I'm currently building a lack enclosure for my printer + hope to have some filters too)
The dust that comes off my filament from printing coats the area after a while. I've never seen naturally blue dust.

[stray notch]

Thats honestly going to be better though!
And you've solved it yourself!

The only thing to watch with that is when pumping cold air (or any air) to the printer, you get warping + and the print can come unstuck.....
So that is why ideally you have exhaust only....and that fan draws in air through the cracks of the enclosure....

But in your case, if you're still planning to keep in the garage (unsure if u said)...that wont work.... Hmm

So you may need a slightly wacky solution....this i've never done....but give it a read and see what you think.
What about "a box in a box" type solution.
One box is the enclosure, which sits inside another slightly bigger box. The bigger box is cooled with cold dry air. The enclosure vents through filters to outside the boxes via axhaust. The exhaust pulls cool air in from the bigger box. That works cos it's air displacement, and the flow will be slower + potentially less disruptive.
For best effeciency, may be worth insulating the heat out... Hmm
There are probably simpler ways, but idk what they are rn.

The filters will provide a decent amount of resistance to airflow, so u may need high cfm fans (see pc radiators)

[true dragon]

This post has been closed due to inactivity.

This post has been inactive for over 1 hour and so has been closed. To reopen this post simply send another message.