✅｜help-forum

Cheap alternative for Raspberry Pi? 23 messages

Apr 10, 2023, 2:41 PM Electronics

Klipper - Bed Mesh issues 9 messages

Apr 10, 2023, 2:09 PM Hardware Other Software

Endstop Pins in Motherboard not working 3 messages

Apr 10, 2023, 1:48 PM Hardware

print surface 38 messages

Apr 10, 2023, 1:47 PM Hardware

improving print quality 27 messages

Apr 10, 2023, 12:46 PM Software

Noise reduction box or something similar 19 messages

Apr 10, 2023, 12:23 PM Hardware Other

Poor quality for the bottom 20% of print 38 messages

Apr 10, 2023, 12:13 PM Other

Advanced linear factor E3d v6 bimetal with bowden 3 messages

Apr 10, 2023, 10:34 AM Other

Printing Problems 6 messages

Apr 10, 2023, 10:23 AM Other

Holes in first layer. 384 messages

Apr 10, 2023, 9:35 AM Other

[Ender 3 Pro] Filament clog stuck in extruder ASSEMBLY 8 messages

Apr 10, 2023, 8:46 AM Hardware

filament gets shred, stops extruding 33 messages

Apr 10, 2023, 8:35 AM Hardware

Zits on in progress layer 7 messages

Apr 10, 2023, 8:00 AM Hardware Software

Curling on specific corner of print 18 messages

Apr 10, 2023, 5:06 AM Hardware

10x10 mesh not accurate? 3 messages

Apr 10, 2023, 4:57 AM Hardware Other

how do I adjust the length of the rod??? 28 messages

Apr 10, 2023, 4:45 AM Hardware

Yesterday a user was helping me and said I could print in abs with the fans off, any1 got fulldeets? 9 messages

Apr 10, 2023, 2:43 AM Hardware

Ender 3 pro e3d v6 cura profile (Direct Drive) 3 messages

Apr 10, 2023, 2:42 AM Hardware

My recent prints have been very dry/weak 3 messages

Apr 10, 2023, 2:38 AM Other

Print Surface 3 messages

Apr 10, 2023, 2:32 AM Hardware

Ender 3 Pro, temp issues 64 messages

Apr 9, 2023, 11:55 PM Hardware

Speed settings not reflective in Cura or in print 15 messages

Apr 9, 2023, 11:46 PM Other

banding on sv06 60 messages

Apr 9, 2023, 11:36 PM Hardware

Need help configuring marlin on a robin nano v3 2 messages

Apr 9, 2023, 11:15 PM Software

rough edges on top left and bottom right 21 messages

Apr 9, 2023, 10:37 PM Hardware

Photon Mono X prints on the whole plate 7 messages

Apr 9, 2023, 10:19 PM Hardware Software

Anyone familiar with CR10 S5? 7 messages

Apr 9, 2023, 8:44 PM Software

Elephants foot -_- 130 messages

Apr 9, 2023, 7:08 PM Other Software

Recompiling marlin to bypass broken mosfet 22 messages

Apr 9, 2023, 6:31 PM Software

sv06 fails to print first time printer 21 messages

Apr 9, 2023, 5:49 PM Hardware Other Software

Electronics help 31 messages

Apr 9, 2023, 5:25 PM Hardware Electronics

wi-fi change mainsail 19 messages

Apr 9, 2023, 5:02 PM Software

how does nozzle size work 13 messages

Apr 9, 2023, 4:51 PM Hardware

reset access to Mainsail 51 messages

Apr 9, 2023, 3:55 PM Software

bl touch 20 messages

Apr 9, 2023, 3:40 PM Hardware

Need Help with Printer 6 messages

Apr 9, 2023, 3:29 PM Other

I have a few issues with my ender 3 pro 9 messages

Apr 9, 2023, 3:01 PM Hardware Software Electronics

mainsail 3 messages

Apr 9, 2023, 1:56 PM Software

Blob and hole during print 11 messages

Apr 9, 2023, 1:30 PM Hardware

Help with gaps 52 messages

Apr 9, 2023, 12:34 PM Other

Which dual 5015 Cooling duct E3MAX 55 messages

Apr 9, 2023, 9:54 AM Hardware Modelling / CAD Other

stringing 18 messages

Apr 9, 2023, 9:15 AM Hardware

First Layer issues 18 messages

Apr 9, 2023, 6:21 AM Hardware

Octopi 7 messages

Apr 9, 2023, 5:45 AM Software Electronics

How can I protect abs plastic against UV light? 94 messages

Apr 9, 2023, 5:15 AM Hardware Other

Ender 3 Pro e3d v6 Err issue 4 messages

Apr 9, 2023, 4:39 AM Hardware

Getting this error uploading from prusaslicer 8 messages

Apr 9, 2023, 1:53 AM Software

Offset center 8 messages

Apr 9, 2023, 1:46 AM Hardware

Is this normal for my Ender 3V2 Neo bed? 12 messages

Apr 9, 2023, 12:24 AM Hardware

is temperature on filament always accurate? 188 messages

Apr 9, 2023, 12:01 AM Hardware