✅｜help-forum

Stripped grub screw holding heater in Heat Block 2 messages

Oct 4, 2023, 2:29 PM Hardware

Calibrate E-Steps Qidi X-Plus (Gen 1) 17 messages

Oct 4, 2023, 1:00 PM Hardware

SD card reader broken 20 messages

Oct 4, 2023, 3:56 AM Hardware Electronics

mk3+ is not exteuding anymore 9 messages

Oct 4, 2023, 3:03 AM Hardware

Neptune 3 troubleshooting 3 messages

Oct 4, 2023, 2:37 AM Hardware Software Electronics

ender 3 pro why is everything bed level leveled except for middle? 4 messages

Oct 4, 2023, 2:32 AM Hardware

Weird layer issues 8 messages

Oct 4, 2023, 1:32 AM Hardware Software

Elegoo Neptune 4 scrapes the print, but not the bed 7 messages

Oct 3, 2023, 11:57 PM Hardware Software

printing for 44 minutes its only on second layer how fix? 10 messages

Oct 3, 2023, 11:38 PM Hardware

Reset-up? 9 messages

Oct 3, 2023, 11:17 PM Hardware Software

Small print island 4 messages

Oct 3, 2023, 8:33 PM Software

Corner Issues 7 messages

Oct 3, 2023, 4:38 PM Hardware

Colappsing sword not extending 5 messages

Oct 3, 2023, 1:55 PM Other Software

Printed a calibration cube, need help fixing some issues 3 messages

Oct 3, 2023, 1:55 PM Hardware

PC vs PEI 5 messages

Oct 3, 2023, 6:10 AM Hardware

Ender 3 V2 997 messages

Oct 3, 2023, 5:00 AM Hardware Software

Dryer Box help please 6 messages

Oct 3, 2023, 3:47 AM Hardware

About to have access to a JG Aurora. What are some things I need to know? 3 messages

Oct 3, 2023, 3:13 AM Hardware

Fixing parts not fitting together 4 messages

Oct 3, 2023, 3:11 AM Hardware

can't get bowden tube out ender 3 v2 neo 11 messages

Oct 3, 2023, 3:06 AM Hardware

ENDER S1 PRO ABL NOT WORKING 6 messages

Oct 3, 2023, 3:00 AM Hardware

screw hole help 3 messages

Oct 3, 2023, 2:55 AM Hardware Modelling / CAD

Help calibrate my 3d printer 6 messages

Oct 3, 2023, 1:47 AM Hardware

Model not manifold 3 messages

Oct 3, 2023, 12:37 AM Modelling / CAD Software

z axis only shows ?? and will not print 3 messages

Oct 2, 2023, 9:58 PM Hardware

thermistor sensor issue 9 messages

Oct 2, 2023, 9:21 PM Hardware

Outside ok, inside OK, top surfaces though not at all... 3 messages

Oct 2, 2023, 8:16 PM Other

I should probably fix it right? 34 messages

Oct 2, 2023, 6:26 PM Other Electronics

Black Smoke of DEATH 3 messages

Oct 2, 2023, 5:52 PM Hardware

help where do theese go 11 messages

Oct 2, 2023, 2:18 PM Electronics

Well that's terrible 4 messages

Oct 2, 2023, 1:48 PM Other

help with Lubricants for Linear rods and Lead screws. 23 messages

Oct 2, 2023, 12:23 PM Hardware

modify downloaded 3d file (fusion 360) 11 messages

Oct 2, 2023, 11:34 AM Modelling / CAD

i have Problems with my z ofset 5 messages

Oct 2, 2023, 5:47 AM Other

3Dbenchy seam and hull problem 4 messages

Oct 2, 2023, 4:36 AM Hardware Other Software

Print Looking different in Slicer 8 messages

Oct 2, 2023, 4:14 AM Modelling / CAD Software

Klipper bed mesh issues / z-offset 425 messages

Oct 2, 2023, 1:55 AM Hardware

Prusa Slicer/Small stringing issue 7 messages

Oct 2, 2023, 1:45 AM Hardware Other Software

Help fixing my klipper config 78 messages

Oct 1, 2023, 11:34 PM Software

Bizarre slicer issue 16 messages

Oct 1, 2023, 8:36 PM Software

linear advance 17 messages

Oct 1, 2023, 8:15 PM Software

level ender 3 v2 bed 9 messages

Oct 1, 2023, 7:58 PM Hardware

Print stalling/freezing 12 messages

Oct 1, 2023, 7:49 PM Hardware

Bootloading 8-bit motherboard problems 24 messages

Oct 1, 2023, 5:42 PM Software

ender 3 max neo thermal resistor error 16 messages

Oct 1, 2023, 5:40 PM Hardware

Bed Leveling 18 messages

Oct 1, 2023, 4:38 PM Hardware Software

Print failed despite good Exposure settings (im new to this) 7 messages

Oct 1, 2023, 3:12 PM Hardware

Klipper adding line to gcode files 14 messages

Oct 1, 2023, 1:06 PM Software

Klipper upgrade for ender 3 3 messages

Oct 1, 2023, 10:25 AM Hardware Software

Kobra-Go mechanical issue. 3 messages

Oct 1, 2023, 3:34 AM Hardware