✅｜help-forum

Normal prints look fine but tolerances are horrible 60 messages

Apr 30, 2024, 1:55 AM Hardware Software

infill squishy 104 messages

Apr 30, 2024, 1:09 AM Hardware

My mom is concerned about PLA fumes, is there any issues that can arise from them? 11 messages

Apr 30, 2024, 1:06 AM Other

144 non-manifold edges in orca slicer 5 messages

Apr 29, 2024, 9:00 PM Modelling / CAD

Sovol SO-06 print trouble 23 messages

Apr 29, 2024, 8:44 PM Hardware

gcode 4 messages

Apr 29, 2024, 8:13 PM Software Electronics

Good first layers on right side but bad on the left 35 messages

Apr 29, 2024, 7:16 PM Hardware

How much to charge client 6 messages

Apr 29, 2024, 6:40 PM Other

movement repetability issue 16 messages

Apr 29, 2024, 1:35 PM Electronics

Neptune 3 Max 8 messages

Apr 29, 2024, 11:48 AM Hardware Electronics Software

Pet bottle to Filament 39 messages

Apr 29, 2024, 11:42 AM Other Electronics

Nozzle Dragging and Knocking Prints Over 3 messages

Apr 29, 2024, 10:09 AM Hardware Software

Ender 3 v2 Print Curling 6 messages

Apr 29, 2024, 5:03 AM Hardware

early layers peeling and bubbling 5 messages

Apr 29, 2024, 2:21 AM Hardware

Best way to load and unload filament on long feed tube? 5 messages

Apr 29, 2024, 1:01 AM Hardware

What the 20 messages

Apr 28, 2024, 10:51 PM Other

some error i dont know how to fin 3 messages

Apr 28, 2024, 10:02 PM Other

Bambu studio help. (ams issue) 6 messages

Apr 28, 2024, 9:27 PM Software

Rough Z seam 3 messages

Apr 28, 2024, 9:26 PM Hardware Software

stuck on boot screen 7 messages

Apr 28, 2024, 8:57 PM Hardware

ultimaker cura crashing?! 3 messages

Apr 28, 2024, 8:47 PM Modelling / CAD Software

TPU layer adhesion 18 messages

Apr 28, 2024, 7:45 PM Hardware

Need help filling a huge gap. 10 messages

Apr 28, 2024, 7:19 PM Other

Need help with klipper for Sovol sv06 plus 5 messages

Apr 28, 2024, 6:42 PM Hardware Software

gcode thumbnail size for ender 3 v3 se and how to show them 3 messages

Apr 28, 2024, 5:20 PM Software

New to 3D printing, any advice on creating this? 4 messages

Apr 28, 2024, 4:22 PM Hardware Other

Layer skipping x plus 3 3 messages

Apr 28, 2024, 4:11 PM Hardware Other Software

vref formula 4 messages

Apr 28, 2024, 3:23 PM Other Software

First time 3d printing 4 messages

Apr 28, 2024, 3:09 PM Other

End g-code (Fix) 2 messages

Apr 28, 2024, 3:07 PM Hardware

support 3 messages

Apr 28, 2024, 2:59 PM Other

ptfe tube needed? 3 messages

Apr 28, 2024, 9:53 AM Hardware

Under Extrusion on curves 6 messages

Apr 28, 2024, 7:36 AM Software

z-seams causing holes in klipper 20 messages

Apr 28, 2024, 6:56 AM Other

Why does this pin look messed up? 5 messages

Apr 28, 2024, 3:33 AM Hardware

Z Endstop Cable 3 messages

Apr 28, 2024, 2:56 AM Hardware

PETG 7 messages

Apr 28, 2024, 1:56 AM Hardware Other Software

walls/corners not printing 5 messages

Apr 28, 2024, 1:19 AM Other

why is my extruder gear clicking? I have a direct extruder 9 messages

Apr 27, 2024, 11:09 PM Other

Can't figure out what settings I need to adjust 3 messages

Apr 27, 2024, 11:08 PM Hardware Software

Voxelab Aquila extruder clicking intermittently 23 messages

Apr 27, 2024, 9:41 PM Hardware

quality problem 3 messages

Apr 27, 2024, 9:13 PM Hardware Software

Nozzle Wont Heat Up on my Ender 3 v2. 7 messages

Apr 27, 2024, 9:05 PM Hardware Electronics

Comes off the bed 3/4 the way done. 11 messages

Apr 27, 2024, 8:49 PM Hardware

filament not being placed correctly 9 messages

Apr 27, 2024, 8:31 PM Other

No extrusion after 11 minutes 96 messages

Apr 27, 2024, 7:24 PM Hardware Software

Very new to resin 3d printing haven't been able to print anything but the one pictured. 3 messages

Apr 27, 2024, 6:38 PM Hardware Other Electronics

ITS NOT WORKING 7 messages

Apr 27, 2024, 6:08 PM Other

Confused by Cura AutoTowers extension in Cura 6 messages

Apr 27, 2024, 5:27 PM Software

Tried to update my firmware but now software doesn't work 37 messages

Apr 27, 2024, 5:12 PM Software