Anyone knows if the friction fit (of the 60HE v2) works with the Holy60 too?

[wicked nacelle]

In Wooting's website says that works on the Tofu Redux, but i like the Holy60 more, i would appreciate if anyone could enlighten me in this subject ^^

[echo summit]

Thanks for posting your support request!

Note: #community_support is only for answering general questions and for troubleshooting.
All order-specific and shipment-specific support must be handled via the Wooting Support Wizard*
(You need to create an account on the Wooting Hub, using the same email address as your purchase. The account is not created for you automatically!)

Troubleshooting your Wooting Keyboard? Try these steps first!
Basic Troubleshooting

Questions about shipping, or what to do if your shipment has a problem?
Possible Problems During Shipping (with Solutions)

Looking for information about your specific order?
You can find that on the Wooting Hub! There you can also add upgrades, update your shipping address, and much more.

Is your order about to ship and you need to pause it for any reason?
Place it on hold via the Wooting Hub!

Do you need to...

• Cancel an order?
• Return/Refund an order?
• Get assistance with placing an order?
• Change the items in your order?
• Change your shipping address to a different country?
• Return a recent purchase?
• Get warranty support?

All of these types of requests need to be made via the Wooting Support Wizard!

[molten ocean]

Yes, it will work, but it's recommended to ground the module by screwing in a single screw on the top right for example.

[wicked nacelle]

wait how would that work tho?

i'm new to modding

i saw that if i use the foam that comes with the 60HE+ on the Holy60 it can warp the pcb, that's why i'm asking as well about the single screw

[molten ocean]

Holy60 comes with a thin piece of poron foam. You place it in the case, then drop the V2 module in. After that, install one screw on the top right corner to ground the module.

[wicked nacelle]

so it will not warp even with one screw holding it, besides de friction fit?

i'm scared of that 😅

oh also if i go for the Tofu Redux do i need to put a screw as well?

[molten ocean]

No, you won't warp anything. Just install one screw loosely, no need to tighten it.

You'll also need to do this with the Tofu60, yes.

[wicked nacelle]

oh so loose fit got it

makes more sense now to me

really appreciate it!

[molten ocean]

Yeah, basically all you need to do is:

1. Install the standoff on the top right corner, as shown in the image
2. Place the foam inside the case
3. Put the V2 module in
4. Screw in the top right screw. Remember it doesn’t need to be tight

[wicked nacelle]

oh one last thing, with the tofu redux i could use the foam or the silicon slab that comes with the wooting right? Also the friction fit is doable bc of the silicone sandwiched in between the pcb and the plate right?

[molten ocean]

Did you order v2 module? If so, case dampening (EPDM foam and silicone block) doesn't come with it. They're only included with the prebuilt or the v2 aluminum case.

[wicked nacelle]

no i'm deciding if i should get the module or the prebuilt

that's why i wanted to know

as well

[molten ocean]

You can use Wooting's foam and silicone block inside the Tofu60 Redux. However, they won't fit in the Holy60 as far as I know, in that case you'll need to use the thin poron foam that comes with it.

[wicked nacelle]

oh alright, and the friction fit is bc of the silicone sandwiched? or something else?

[molten ocean]

Yeah, v2 module has silicone friction fit pad pre-installed between the PCB and plate. It holds the module securely in place using friction.

[wicked nacelle]

nice

that way i can choose

thank you!

oh on the tofu redux, where do i screw loosely?

[wicked nacelle]

thank you, why those two tho? i would understand if was for the usb port, but it isn't

[molten ocean]

Not two, just one. I showed where you should install the screw.
The reason for putting it in the top right corner is that you rarely use the right side of the board compared to the left, so using the screw there won't really affect the typing experience. You'll still benefit from the friction fit pad even with the screw installed.

[wicked nacelle]

oh i meant those two in like the tofu and holy60

[wicked nacelle]

oh, thanks for the explanation, could i put O rings on the screw? like so the screw doesn't make direct contact to the pcb and the case?

or would be too much?

[molten ocean]

I'd recommend using the screw only, without o ring.

[wicked nacelle]

alright, thank you! <3

[wicked nacelle]

sorry for annoy you once more, but if i get the optimum case do i have to use the foam it comes with or can i chose to use either the silicone or the foam that comes with the wooting 60HE?

[molten ocean]

60HE v2 EPDM foam and silicone block make the module sit higher in the Optimum case, which may cause the USB port to not align perfectly, so best to use the Optimum case foam.

[wicked nacelle]

alright thank you

[wicked nacelle]

i decided to get the 60HE v2 module, once again really appreciate the help, also am i going to get the new role after getting the keyboard?

[molten ocean]

Yes, claim it in the Wooting hub
https://youtu.be/6hmRHWZSeXw

[wicked nacelle]

also it doesn't show in my orders?

[molten ocean]

Takes time, should show up in 15-20 minutes

[wicked nacelle]

ah, for a second i got scared ahah

thank you, wanted to confirm that i chose the normal space bar ahah

[wicked nacelle]

btw this is normal right?

[wicked nacelle]

is this an automatic update or is really only coming in january?

asking bc when i scroll down a bit more this appears