warped tendon
No discussions here, only reactions thank you
Base Mods:
GH60 (Tofu V1 clone)
PC plate
Lube Switches (Krytox 205g0)
Stock Stabs (Lubed Housing and Stem with Krytox 205g0, Dieletric Grease on Wire, Holee Mod)
Switch Tape Mod (3 layers of gentle paper tape)
Bandaid mod (Dry)
Tempest mod (1 layer Masking Tape)
Gloirous GBPT Keycaps
Poron Switch Pads
Independent mods:
Mounting style
PCB Foam
Case Foam
v-- Gummy mount, No pcb foam, Wooting Case Foam
Gummy mount
No Pcb foam
No case foam
warped tendon
Tray Mount
No Pcb foam
Wooting Case foam
Tray Mount
Silicone pcb foam
Wooting Case foam
TenZ Jr Wooting Alu Configuration (No discussions here, only reactions thank you)
Tray Mount
Silicone Pcb foam
No case foam
warped tendon
Warning this mod will take 4-7 hours or more.
The Switch Tape Mod, made for the Lekker switches, was purposely aimed to reduce or eliminate the full chattering effect of the top housing and stem. Another effect of the mod is stem wobble being reduced depending on the amount of layers used. The maximum layer you can do is three, as two is recommended. Be aware that three layers will fully eliminate the chatter noise and will reduce stem wobble by a lot; another thing to note when performing the mod make sure the tape is fully pressed down flat, as you will have issues with the stem being stuck or having a big bump of tactility. So to perform the mod, you need gentle paper tape (aka medical tape) and tweezers. Starting, you will need to cut a specific or estimated size of the top housing’s stem rails. If doing multiple layers, cut multiple strips, and stack them together. Once that step is done, cut your strip in half, both pieces will be placed on both sides of the top housing which will be shown in the pictures. Then fold the strips into the internals of the top housing then make sure the tape is fully pressed down flat as said from the awareness. If needed, lube a very light layer on the tape if there is either scratchiness or a little tactility bump. After all that your first switch is completed! Now repeat this 60 more times :)
Gentle Paper Tape (Medical Tape)
Cut the tape into a specific or estimated size that would fit the stem rails of the top housing and if doing multiple layers (which is most likely) stack them together.
Then cut the stack of strips in half as it will serve as two pieces that will go on both sides of the top housing. Place one strip on one side, making sure it sticks, then fold it into the internal top housing and press down flat to confirm a secure stick. Once done, do it on the other side. And it should look like this.
If needed (recommended) lube a light layer on the tape to prevent scratchiness or little tactility bump.
Once you're done, put the switch back together making sure the stem returns to its initial position. Then tada! Your first switch tape modded switch is completed. Now repeat 60 more times and enjoy (even though you wont 🤭).
manic swallow
Once you're done, put the switch back together making sure the stem returns to i...
Bro you’re awesome, thank you 🙏🏽
Only one question, for the inside of the housing, how far down do you allow the tape to go? Do you allow it to touch the clips that clip into the bottom housing or try to have the tape stop right above the clips?
warped tendon
Only one question, for the inside of the housing, how far down do you allow the ...
right above the clips
manic swallow
Based on photos, it looks like right above the clips but wanted to ask
Okay thanks
This is super easy to follow bro, good job
warped tendon
If anybody has a question
Pls ping me in #🔧│keyboard_modding I'm trying to keep this thread as clean as possible
royal elm
**Warning this mod will take 4-7 hours or more.**
The Switch Tape Mod, made for ...
Thats a very interesting idea, tried it with a bandaid (which is propably to thick and sticky) and it works, completely muted. I wonder how you fit 3 layers in there and the stem still comes up.
outer silo
Thats a very interesting idea, tried it with a bandaid (which is propably to th...
Gentle medical tape is thin enough to be able to fit 3 layers
pine oxide
Sounds amazing but I wonder about the longevity , gonna try regardless. Ty
warped tendon
(sorry, try to keep this thread clean as possible
dont want it to end up like the other one, compliments is fine but try to avoid anything that would make discussions)
warped tendon
Gummy mount
No pcb foam
Polyfill
(2 layer tempest and new TX AP Stabilizers:Still in work)
warped tendon
**My 14-15 y/o setup (late 2022-2023) **
Dec 14 2022, when it all started
1 month when I got my Wooting and doing modding research (Apr 5 2023)
When I got my GBPT key caps and when my hardcore modding journey began (May 30 2023 )
Alu case gifted during Nov from Tirade, and current setup of the start in 2024 (Mouse and mouse pad upgrade, additional stuff like boom arm)
warped tendon
Alu case gifted during Nov from Tirade, and current setup of the start in 2024 (...
Changed mic (Fifine K688 | Prob try to get IEMS, need some recommendations)
Enter and Right Shift sound test (Mar 4 2024)
TenZ History, Alu Configs, Switch Tape Mod Guide
Thockson History, Alu Configs, Switch Tape Mod Guide
Thockson Setup History, Alu Configs, Switch Tape Mod Guide
Switch Tape Mod Guide, Alu Configs, Thockson Setup History
manic swallow
I’m not sure, why?
manic swallow
I’m not sure, why?
The red is just a different color, no? Or did it show different specs?
(You can delete these messages when done with conversation)
send link
They're slightly better
Basically a revision of the OG ones
manic swallow
They have some good reviews too
warped tendon
They have some good reviews too
will delete this convo now thanks again
warped tendon
Wooting 60HE
GH60 Tofuv1 Clone
Gummy/Friction Mount
Lekker60 (Switch Tape Mod)
TX AP Stabs (Fully Stock)
PC Plate
Silicone Pad
Poron Switch Pads
Tempest Mod (1 Layer Masking Tape)
Polyfill
Glorious GPBT Keycaps
warped tendon
New desk 
