build-help

Not cutting properly for prints 67 messages

Mar 5, 2026, 2:40 PM Tuning BoxTurtle

Turtleneck not working properly 14 messages

Mar 4, 2026, 11:02 PM Tuning BoxTurtle

[Solved] Pauses after every color change 13 messages

Mar 4, 2026, 4:20 PM BoxTurtle Initial Setup

[SOLVED ]EMI USB disconnect s specifically to AFC-Lite when grounding stepper motors by 56 messages

Mar 3, 2026, 2:41 PM BoxTurtle

Enclosure Frame Cut and Drill Guide 6 messages

Mar 2, 2026, 1:56 PM BoxTurtle

[Solved] Printer shuts down on Z Tilt Adjust command after adding BT. 75 messages

Feb 27, 2026, 8:06 PM BoxTurtle Build Issue Initial Setup

[solved] nylock issue? 5 messages

Feb 27, 2026, 7:49 PM BoxTurtle

Filament Cutter For Bed Slingers 5 messages

Feb 26, 2026, 7:38 PM HTLF

[solved] Extruding a string from nozzle prior to cutting. 12 messages

Feb 26, 2026, 5:18 PM BoxTurtle Initial Setup

Brush Macro 26 messages

Feb 26, 2026, 1:20 AM BoxTurtle

Lane 3 issue 5 messages

Feb 25, 2026, 6:09 PM Tuning BoxTurtle Build Issue Other

What gauge wire should I use to power the afc? 9 messages

Feb 24, 2026, 12:42 AM BoxTurtle Initial Setup

Turtle neck switches 9 messages

Feb 23, 2026, 8:20 PM Initial Setup

Strange filament requirements, what should I buy? 10 messages

Feb 23, 2026, 2:20 PM BoxTurtle Build Issue Initial Setup

[Solved] 2 lanes, respooler won't respool? 19 messages

Feb 22, 2026, 11:35 PM Tuning Initial Setup

Cannot get a perfect fit on some of the STLs. 5 messages

Feb 20, 2026, 4:23 PM BoxTurtle Build Issue

Help with tip forming 25 messages

Feb 17, 2026, 10:06 PM Tuning BoxTurtle Other

[SOLVED] All Lanes empty, but lane 1 says "locked and loaded" 13 messages

Feb 17, 2026, 12:05 AM Initial Setup

Need help calibrating filament loads/unloads 135 messages

Feb 16, 2026, 11:53 PM BoxTurtle Build Issue

Can't Flash board dfu error 3 messages

Feb 16, 2026, 5:36 AM BoxTurtle Initial Setup

[Solved] Respoolers not moving during EJECT move 3 messages

Feb 10, 2026, 9:00 AM BoxTurtle Build Issue

Tool must be unloaded to calibrate system . 11 messages

Feb 10, 2026, 12:50 AM Tuning BoxTurtle Other

Timer Too Close Error 107 messages

Feb 9, 2026, 7:21 AM BoxTurtle

Help needed trying to get rapido hotend working with an A4T (constant nozzle buildup) 11 messages

Feb 8, 2026, 7:31 AM Tuning BoxTurtle Build Issue Initial Setup

BoxTurtle Not Loading Reliably 47 messages

Feb 8, 2026, 5:33 AM BoxTurtle

buffer ram variation 9 messages

Feb 7, 2026, 4:10 PM Tuning

Help flashing AFC-Lite with Leviathan 1.2 in USB-CAN-Bridge 17 messages

Feb 6, 2026, 7:07 PM BoxTurtle Initial Setup

No leds and no respoolers 4 messages

Feb 6, 2026, 2:37 PM BoxTurtle

Not sure if I need to reprint 7 messages

Feb 5, 2026, 10:05 PM BoxTurtle Build Issue

No extrude on voron only box turtle when pressing extrude button 3 messages

Feb 5, 2026, 2:34 PM Build Issue

Enclosure + PolyDryer not hot enough 7 messages

Feb 5, 2026, 2:08 AM BoxTurtle

[solved] Help with filament pathing around BTT smart sensor 64 messages

Feb 3, 2026, 6:06 AM BoxTurtle Build Issue Other

TTC after BRUSH Macro. 22 messages

Feb 3, 2026, 2:02 AM Build Issue

Expanded and compressed help please 3 messages

Feb 2, 2026, 2:28 PM BoxTurtle Build Issue

[solved] Spool Assist motors act like they are jammed 15 messages

Jan 30, 2026, 8:08 PM BoxTurtle

Unknown short while loading filament 21 messages

Jan 29, 2026, 10:32 PM BoxTurtle Build Issue Initial Setup

[Solved] Tips for Inserting ECAS into TurtleNeck Frame? 5 messages

Jan 28, 2026, 1:11 PM Build Issue

[solved] N20 motor help 7 messages

Jan 27, 2026, 1:16 PM BoxTurtle

[solved] Help needed: Severe clogging during filament changes 13 messages

Jan 27, 2026, 12:37 PM BoxTurtle

[solved] Where to source rubber seals (formbot kit) 9 messages

Jan 27, 2026, 4:07 AM BoxTurtle Build Issue

tool start sensor flicker 14 messages

Jan 26, 2026, 6:10 PM Build Issue

Lane 2 doesnt retract enough? 7 messages

Jan 25, 2026, 4:00 PM Tuning BoxTurtle

[Solved] Error happened when trying to save variables, check AFC.log for error 6 messages

Jan 23, 2026, 1:13 PM BoxTurtle

BT not reliably pushing filament 78 messages

Jan 22, 2026, 7:52 PM BoxTurtle Initial Setup

"Resonance" occurs during high flow-rate 32 messages

Jan 22, 2026, 3:52 PM BoxTurtle Other

120ohm jumper on afc lite when not using can. 2 messages

Jan 22, 2026, 3:37 PM BoxTurtle Build Issue

Setting up a new AFC-Lite 113 messages

Jan 22, 2026, 1:00 AM BoxTurtle Build Issue Initial Setup

home sensor doesn't get detected. 16 messages

Jan 21, 2026, 2:57 PM HTLF Initial Setup

[solved] 2 extruders refuse to work need help adjusting beuilding 23 messages

Jan 21, 2026, 7:14 AM Build Issue

[solved] AFC_Cut breaking depressor after first cut on purge calibraton print 16 messages

Jan 21, 2026, 1:25 AM Tuning BoxTurtle Build Issue Initial Setup